"AF" pad? KPA100

[dave.wilburn]

Page 21 of the KPA100 document (version D).  In the initial tests, right
column, second row from the bottom of the table;

"AF" pad (measure from bottom), ground   > 10k

What is the "AF" pad?  I assume I am supposed to measure it from the
bottom of the board, to ground, and it is to be greater than 10k.  But I
can't sort out what "AF" pad is.  I even checked the version E document.
  So it is probably something obvious that I am just not getting.
--

David Wilburn
[hidden email]
K4DGW
K2 #5982
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Lambs, Dick & Judy]

On Apr 10, 2007, at 4:48 , David Wilburn wrote:

> Page 21 of the KPA100 document (version D).  In the initial tests,  
> right column, second row from the bottom of the table;
>
> "AF" pad (measure from bottom), ground   > 10k
>
> What is the "AF" pad?  I assume I am supposed to measure it from  
> the bottom of the board, to ground, and it is to be greater than  
> 10k.  But I can't sort out what "AF" pad is.  I even checked the  
> version E document.  So it is probably something obvious that I am  
> just not getting.
> --

Look at the board from the top, with the speaker cut-out to the lower  
right.  Now notice the lower left corner.  You'll see holes (i.e.,  
solder points or "pads") for "GND" and "AF."  The "AF" solder point  
is the AF pad.  It's where the audio line from the K2 connects to the  
board.

I just finished a KPA100, and I have to admit that description  
stumped me for a moment, also.

Dick, K0KK
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[dave.wilburn]

Thanks much.

David Wilburn
[hidden email]
K4DGW
K2 #5982


Lamb, Dick & Judy wrote:

>
> On Apr 10, 2007, at 4:48 , David Wilburn wrote:
>
>> Page 21 of the KPA100 document (version D).  In the initial tests,
>> right column, second row from the bottom of the table;
>>
>> "AF" pad (measure from bottom), ground   > 10k
>>
>> What is the "AF" pad?  I assume I am supposed to measure it from the
>> bottom of the board, to ground, and it is to be greater than 10k.  But
>> I can't sort out what "AF" pad is.  I even checked the version E
>> document.  So it is probably something obvious that I am just not
>> getting.
>> --
>
> Look at the board from the top, with the speaker cut-out to the lower
> right.  Now notice the lower left corner.  You'll see holes (i.e.,
> solder points or "pads") for "GND" and "AF."  The "AF" solder point is
> the AF pad.  It's where the audio line from the K2 connects to the board.
>
> I just finished a KPA100, and I have to admit that description stumped
> me for a moment, also.
>
> Dick, K0KK
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com