About Keyboard for K3 for digital or CW mode (Without PC)

[giuliano-8]

I have tested this interface to add a Keyboard for IC-756 pro line and is
working well.
I think that can be used for K3 too. This interface can be used to generate
CW or RTTY, on K3 can traslate  CW to PSK31 too.
Schematic is minimal, also LCD can be removed, so only a programmed PIC (
.hex free available)+ some resitors are necessary.
So total components are:  a  standard PC Keyboard, a programmed PIC and some
resitors.
If anyone is able to program a PIC18F2620 a can send the .hex code, if not I
can ship the programmed PIC at empty PIC cost
Anyone can build easily this interface yourself.
See more at http://www.i0cg.com/rtty.htm
73
Giuliano I0CG
My personal K3 arrives around September/October



_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[wb2ssb]

How detrimental would it be if I broke up the power cable going to my K3
into two segments, joined by a two pair of Anderson power poles?  Is
this sheer stupidity on my part?  (It would be convenient for me to do
this, but not if it introduces more problems than it solves).

Thanks in advance for any answer!

------------------------------------------------------------
This email message, including any attachments, is for the sole use of the intended recipient(s) and may contain information that is proprietary, confidential, and exempt from disclosure under applicable law. Any unauthorized review, use, disclosure, or distribution is prohibited. If you have received this email in error please notify the sender by return email and delete the original message. Please note, the recipient should check this email and any attachments for the presence of viruses. The organization accepts no liability for any damage caused by any virus transmitted by this email.
=================================
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[.k8dd.-2]

If you used #10 wire .....
Check out the July 2008 CQ magazine, page 74, the Beginners Corner column.
There is a very good write-up on page 79 on how to do this.
I suppose you could use #12 wire if your current requirements were lower on
each leg.

73    Hank    K8DD

----- Original Message -----
From: "Sanger, Joseph" <[hidden email]>
To: <[hidden email]>
Sent: Sunday, July 20, 2008 11:57 AM
Subject: RE: [Elecraft] About Keyboard for K3 for digital or CW mode
(WithoutPC)


How detrimental would it be if I broke up the power cable going to my K3
into two segments, joined by a two pair of Anderson power poles?  Is
this sheer stupidity on my part?  (It would be convenient for me to do
this, but not if it introduces more problems than it solves).

Thanks in advance for any answer!

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com