Antenna 2

[Paul Ormandy]

Thanks for the replies. Hadn't thought of its use for sub rx or dummy load.
I have grounded out the connector with a plug hooked directly to the
receiver grounding terminal.

Paul
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Jim Rhodes-2]

Well if you accidentally transmit into it an open might be better than a
short. Did you at least disable it using the utility program?

Jim Rhodes
K0XU

On Nov 28, 2017 16:52, "Paul Ormandy" <[hidden email]> wrote:

> Thanks for the replies. Hadn't thought of its use for sub rx or dummy load.
> I have grounded out the connector with a plug hooked directly to the
> receiver grounding terminal.
>
> Paul
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Bob McGraw - K4TAX]

Either put a small 50 ohm load or leave it open.  A short to ground may cause a PA device failure.

Bob, K4TAX


Sent from my iPhone

> On Nov 28, 2017, at 5:19 PM, Jim Rhodes <[hidden email]> wrote:
>
> Well if you accidentally transmit into it an open might be better than a
> short. Did you at least disable it using the utility program?
>
> Jim Rhodes
> K0XU
>
>> On Nov 28, 2017 16:52, "Paul Ormandy" <[hidden email]> wrote:
>>
>> Thanks for the replies. Hadn't thought of its use for sub rx or dummy load.
>> I have grounded out the connector with a plug hooked directly to the
>> receiver grounding terminal.
>>
>> Paul
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:[hidden email]
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to [hidden email]
>>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]