CORRECTION Re: SB-221 for K3 need some help.

[Don Rasmussen]

Thanks Bill,

I don't *think* I received any special treatment from
the factory, I just sent and email to the guy that
created the transceiver. Amazing. I got a response in
less than an hour, a quote from an actual user of my
configuration. To those reading this, Elecraft will
spoil you for life, never think about buying anything
other - hi.

Yes, I turned off QSK and have a decent long delay in
semi-break in. I had a QSO with NH6SV tonight and he
reports a clean signal st 599.

I thought I had Tom cornered on no reason to install
that soft key but I like his answer. In addition, I
had the amp apart several times today and it provided
me with a renewed respect for that little innocent
looking line. ;-) Beforte that comment he made, I
would not have bothered shutting off both units before
connecting / disconnecting. Until or unless I install
soft key, will maintain that procedure.

..


[Elecraft] CORRECTION Re: SB-221 for K3 need some
help.
Bill W5WVO w5wvo at cybermesa.net
Sun Aug 31 17:17:45 EDT 2008

Oops, correction. Looks like the K3 will handle the
SB-220's T-R relay coil voltage after all. Sorry about
that, my bad. You still need to worry about the
closure timing, though. I have my K3 set to the max
(20 ms) and there doesn't SEEM to be a probelm -- but
I've never actually measured how longs it takes the
original Heath frame relay to close. You really should
do that.

Bill W5WVO


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Don Rasmussen]

Oh - by the way - my Sb-221 bandswitch is in a
shambles but I hard wired the amp for 20 meters until
a new switch arrives. I learned a valuable lesson,
bandswitches are delicate, close tolerance devices -
don't ever try to repair one that is cracked - hi -
but the contacts can be replaced if the wafer is good.

Time was, I would never consider working on an amp -
too intimidating. But after a couple K2's, soldering
up those big anough to fit in your hands parts seemed
to be a piece of cake!!!


--- Don Rasmussen <[hidden email]> wrote:

> Thanks Bill,
>
> I don't *think* I received any special treatment
> from
> the factory, I just sent and email to the guy that
> created the transceiver. Amazing. I got a response
> in
> less than an hour, a quote from an actual user of my
> configuration. To those reading this, Elecraft will
> spoil you for life, never think about buying
> anything
> other - hi.
>
> Yes, I turned off QSK and have a decent long delay
> in
> semi-break in. I had a QSO with NH6SV tonight and he
> reports a clean signal st 599.
>
> I thought I had Tom cornered on no reason to install
> that soft key but I like his answer. In addition, I
> had the amp apart several times today and it
> provided
> me with a renewed respect for that little innocent
> looking line. ;-) Beforte that comment he made, I
> would not have bothered shutting off both units
> before
> connecting / disconnecting. Until or unless I
> install
> soft key, will maintain that procedure.
>
> ..
>
>
> [Elecraft] CORRECTION Re: SB-221 for K3 need some
> help.
> Bill W5WVO w5wvo at cybermesa.net
> Sun Aug 31 17:17:45 EDT 2008
>
> Oops, correction. Looks like the K3 will handle the
> SB-220's T-R relay coil voltage after all. Sorry
> about
> that, my bad. You still need to worry about the
> closure timing, though. I have my K3 set to the max
> (20 ms) and there doesn't SEEM to be a probelm --
> but
> I've never actually measured how longs it takes the
> original Heath frame relay to close. You really
> should
> do that.
>
> Bill W5WVO
>
>
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com