Elecraft

CW Sidetone and Line Out?

Classic

List

Threaded

3 messages Options

Dana Roode

CW Sidetone and Line Out?

I typically use a telephone connection for receive audio from my remote K3
as its one less dependence on the crummy internet I have. That broke today
so I'm using audio over the Internet using DF3CB REMAUD program. My CW
sidetone is loud no matter what I set "MON" too, and I've even experimented
with the "LINOUT" configuration; setting it to 0 removes my receive
audio but not the sidetone.

It seems sidetone is coming from LINOUT and I've not found a way to reduce
its amplitude. Or I am not thinking about this right...

Any suggestions?

Dana
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Bob Wilson, N6TV

Re: CW Sidetone and Line Out?

There's a special setting only documented in the K3 Firmware Release Notes
<ftp://ftp.elecraft.com/K3/firmware/hfwnotes.rtf> as follows:

* TX LINE OUT (MONITOR) LEVEL NOW ADJUSTABLE: In CONFIG:LIN OUT menu entry,
tap '2' (REV switch) to set the "T=" level (TX monitor). Tap '2' again to
return to the RX LINE OUT setting.

So if you go to CONFIG:LIN OUT, then tap [2], you can change the sidetone
(monitor) level.

73,
Bob, N6TV

On Wed, Aug 19, 2020 at 3:24 PM Dana Roode K6NR <[hidden email]>
wrote:

> I typically use a telephone connection for receive audio from my remote K3
> as its one less dependence on the crummy internet I have. That broke today
> so I'm using audio over the Internet using DF3CB REMAUD program. My CW
> sidetone is loud no matter what I set "MON" too, and I've even experimented
> with the "LINOUT" configuration; setting it to 0 removes my receive
> audio but not the sidetone.
>
> It seems sidetone is coming from LINOUT and I've not found a way to reduce
> its amplitude. Or I am not thinking about this right...
>
> Any suggestions?
>
> Dana
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Dana Roode

Re: CW Sidetone and Line Out?

Wow thanks Bob. I thought I was going nuts and wasn't sure where the
sidetone was coming from. Seems odd that the normal mon control doesn't
affect this but I'm sure Elecraft had it's reasons.

Thanks again, Dana

On Thu, Aug 20, 2020, 4:35 PM Bob Wilson, N6TV <[hidden email]> wrote:

> There's a special setting only documented in the K3 Firmware Release Notes
> <ftp://ftp.elecraft.com/K3/firmware/hfwnotes.rtf> as follows:
>
> * TX LINE OUT (MONITOR) LEVEL NOW ADJUSTABLE: In CONFIG:LIN OUT menu
> entry, tap '2' (REV switch) to set the "T=" level (TX monitor). Tap '2'
> again to return to the RX LINE OUT setting.
>
> So if you go to CONFIG:LIN OUT, then tap [2], you can change the sidetone
> (monitor) level.
>
> 73,
> Bob, N6TV
>
>
> On Wed, Aug 19, 2020 at 3:24 PM Dana Roode K6NR <[hidden email]>
> wrote:
>
>> I typically use a telephone connection for receive audio from my remote K3
>> as its one less dependence on the crummy internet I have. That broke
>> today
>> so I'm using audio over the Internet using DF3CB REMAUD program. My CW
>> sidetone is loud no matter what I set "MON" too, and I've even
>> experimented
>> with the "LINOUT" configuration; setting it to 0 removes my receive
>> audio but not the sidetone.
>>
>> It seems sidetone is coming from LINOUT and I've not found a way to reduce
>> its amplitude. Or I am not thinking about this right...
>>
>> Any suggestions?
>>
>> Dana
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:[hidden email]
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to [hidden email]
>>
>