Cannot get to "Config" menu after installing KPA3

[Dave (K7DRT)]

I just finish assembling my K3/100.

All went well until that last step of installing the KPA3. Now if I attempt to go to the CONFIG menu the radio beeps (It cycles from normal to main). The config menu never appears.

I updated firmware using the K3 Utility. The problem still exists.

The utility transmit calibration menu has the 50 watt test not highlighted (not available).

I will look at responses to this before pulling the KPA3 out.

Thanks and 73,

Dave (K7DRT)

Tucson, Az.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Iain MacDonnell - N6ML-2]

Just to be sure .. you are HOLDing the MENU button to try to get to
config, right? Two taps won't get you there....

73,

    ~iain / N6ML



On Sat, Apr 7, 2012 at 11:53 PM, Dave (K7DRT) <[hidden email]> wrote:

> I just finish assembling my K3/100.
>
> All went well until that last step of installing the KPA3. Now if I attempt to go to the CONFIG menu the radio beeps (It cycles from normal to main). The config menu never appears.
>
> I updated firmware using the K3 Utility. The problem still exists.
>
> The utility transmit calibration menu has the 50 watt test not highlighted (not available).
>
> I will look at responses to this before pulling the KPA3 out.
>
> Thanks and 73,
>
> Dave (K7DRT)
>
> Tucson, Az.
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dick Dievendorff]

The K3 Utility doesn't know the KPA3 is there unless you enable the KPA3
configuration menu selection.

Dick, K6KR


-----Original Message-----
From: [hidden email]
[mailto:[hidden email]] On Behalf Of Dave (K7DRT)
Sent: Saturday, April 07, 2012 8:53 PM
To: [hidden email]
Subject: [Elecraft] Cannot get to "Config" menu after installing KPA3

I just finish assembling my K3/100.

All went well until that last step of installing the KPA3. Now if I attempt
to go to the CONFIG menu the radio beeps (It cycles from normal to main).
The config menu never appears.

I updated firmware using the K3 Utility. The problem still exists.

The utility transmit calibration menu has the 50 watt test not highlighted
(not available).

I will look at responses to this before pulling the KPA3 out.

Thanks and 73,

Dave (K7DRT)

Tucson, Az.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html