Daisy Chain

[David Christ]

Connecting the PC to the P3 and then the P3 to the K3 was recently
discussed.  When I look at the manual for the KPA 500 it shows the PC
connected to the KPA 500 but only the AUX to the K3 even though there
is a RS 232 connector marked (XCVR).

So, can one chain the PC through the KPA 500 to the K3 the came way
as with the P3 and K3? Can you chain all three together?  if so in
what order?  If one has a KPA 500 and K3 it would be nice not to have
to swap cables for doing updates etc.

This does not seem to be covered in the KPA 500 manual but somehow
seems to be implied by the conductor labeling.  It only mentions
connecting the (XCVR) connector to a Kenwood tranceiver.

David K0LUM
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dick Dievendorff]

The KPA500 owner's manual covers this on page 7, the description of all the
back panel connectors:

"Optional: RS232 (XCVR) {8} connects the KPA500 to a Kenwood transceiver
using a standard 9-pin serial cable".  

That's all it's used for.  

The KPA500 does not "pass thru" commands (or K3 firmware) from one RS-232
connector to another as does the P3.

I use a DB-9 ABCD 4-way switch box to connect a single KUSB to  

A) a P3 and through that to one K3,
B) a second K3 without a P3,
C) a KPA500, and
D) a serial data cable used for the W2, XG3, and K144XV.

My work requires me to load firmware more often than most, and I also tired
of swapping connectors a lot.

Dick, K6KR


-----Original Message-----
From: [hidden email]
[mailto:[hidden email]] On Behalf Of David Christ
Sent: Saturday, August 27, 2011 8:33 AM
To: [hidden email]
Subject: [Elecraft] Daisy Chain

Connecting the PC to the P3 and then the P3 to the K3 was recently
discussed.  When I look at the manual for the KPA 500 it shows the PC
connected to the KPA 500 but only the AUX to the K3 even though there is a
RS 232 connector marked (XCVR).

So, can one chain the PC through the KPA 500 to the K3 the came way as with
the P3 and K3? Can you chain all three together?  if so in what order?  If
one has a KPA 500 and K3 it would be nice not to have to swap cables for
doing updates etc.

This does not seem to be covered in the KPA 500 manual but somehow seems to
be implied by the conductor labeling.  It only mentions connecting the
(XCVR) connector to a Kenwood tranceiver.

David K0LUM
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[AC7AC]

CONTENTS DELETED

The author has deleted this message.