Decode 1 signal only

[zl2hgr]

Greetings
New to group and 1st posting
I am having a play with CWskimmer. I would like to know if it possible to
set it up to receive only one signal, if so how do I go about it.
Cheers
Tom Dixon
E.P.C # 1101
[hidden email]
Madness does not always howl. Sometimes, it is the quiet voice saying, "Hey,
is there room in your head for one more?"
 


No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.516 / Virus Database: 269.20.4/1277 - Release Date: 13/02/08
8:00 p.m.
 

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Greg - AB7R]

I havn't used it yet.  But it seems to work on the audio output from the radio.  If
that's the case it seems it would only decode signals that are in your RX filter BW.  
Isolating the signal you want and narrowing down the filter should give you what you
are looking for....I think.  :)  

-------------------------
73,
Greg - AB7R
Whidbey Island WA
NA-065
K3#0009

On Wed Feb 13 20:45 , zl2hgr  sent:

>Greetings
>New to group and 1st posting
>I am having a play with CWskimmer. I would like to know if it possible to
>set it up to receive only one signal, if so how do I go about it.
>Cheers
>Tom Dixon
>E.P.C # 1101
>[hidden email]
>Madness does not always howl. Sometimes, it is the quiet voice saying, "Hey,
>is there room in your head for one more?"
>
>
>
>No virus found in this outgoing message.
>Checked by AVG Free Edition.
>Version: 7.5.516 / Virus Database: 269.20.4/1277 - Release Date: 13/02/08
>8:00 p.m.
>
>
>_______________________________________________
>Elecraft mailing list
>Post to: [hidden email]
>You must be a subscriber to post to the list.
>Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
>
>Help: http://mailman.qth.net/subscribers.htm
>Elecraft web page: http://www.elecraft.com

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Julian, G4ILO]

Greg - AB7R wrote

I havn't used it yet.  But it seems to work on the audio output from the radio.  If

that's the case it seems it would only decode signals that are in your RX filter BW.  

Isolating the signal you want and narrowing down the filter should give you what you

are looking for....I think.  :)  

There is a two page write up on this program in the latest RadCom, arrived today. One of the things it mentioned is that the program apparently doesn't work well if any filtering is used. It wants a wide band input taken from the IF, not a regular audio output, or its decoding abilities suffer. Don't ask me why.

It's most depressing, reading how the software helped the author spot the exact frequency that successful callers were using, so he could call on the same frequency and make a contact with the DX right away, while others without the software, unable to spot the exact frequency to call on, went unanswered. A key skill that allowed the less well equipped station to get an advantage over those with more power but less operating prowess, has been wiped out by a bit of shareware. :(

(To forestall a possible deluge of requests for copies of the article, sorry but I don't posssess a scanner, even if I was willing the RSGB's copyright.)

[Charly]

Many DX load a set of memory freqs. spread over their announced listening spread and then punch the memory button after each contact, insuring that the DX will not hear a second caller on the same freq.  73Charles [hidden email] > Date: Thu, 14 Feb 2008 14:54:46 -0800> From: [hidden email]> To: [hidden email]> Subject: Re: [Elecraft] Decode 1 signal only> > > > Greg - AB7R wrote:> > > > I havn't used it yet. But it seems to work on the audio output from the> > radio. If > > > > that's the case it seems it would only decode signals that are in your RX> > filter BW. > > > > Isolating the signal you want and narrowing down the filter should give> > you what you > > > > are looking for....I think. :) > > > There is a two page write up on this program in the latest RadCom, arrived> today. One of the things it mentioned is that the program apparently doesn't> work well if any filtering is used. It wants a wide band input taken from> the IF, not a regular audio output, or its decoding abilities suffer. Don't> ask me why.> > It's most depressing, reading how the software helped the author spot the> exact frequency that successful callers were using, so he could call on the> same frequency and make a contact with the DX right away, while others> without the software, unable to spot the exact frequency to call on, went> unanswered. A key skill that allowed the less well equipped station to get> an advantage over those with more power but less operating prowess, has been> wiped out by a bit of shareware. :(> > (To forestall a possible deluge of requests for copies of the article, sorry> but I don't posssess a scanner, even if I was willing the RSGB's copyright.)> > -----> Julian, G4ILO K3 s/n: 222 K2 s/n: 392> G4ILO's Shack: www.g4ilo.com> Zerobeat Ham Forums: www.zerobeat.net/smf> -- > View this message in context: http://www.nabble.com/Decode-1-signal-only-tp15473995p15491147.html> Sent from the Elecraft mailing list archive at Nabble.com.> > _______________________________________________> Elecraft mailing list> Post to: [hidden email]> You must be a subscriber to post to the list.> Subscriber Info (Addr. Change, sub, unsub etc.):> http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm> Elecraft web page: http://www.elecraft.com_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com