FT8 and KX3
Locked
 
|
New to FT8 and KX3 operation.
I cannot seem to get them communicating. Error message hamlib failure. Suggestions? Bob KI0G ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Bob,
Select the K3 in Hamlib if the KX3 is not present in the selections. Other than that I cannot help much with the computer end setup. FT8 is no different than other soundcard data modes. On the KX3 part, set the DATA mode to DATA A. Ignore the common internet advice for setting the audio and power levels (and the WSJT-X instructions), and set the KX3 audio level to indicate 4 bars on the ALC meter with the 5th bar flashing. Control the power with the power knob. There is an article on my website www.w3fpr.com to assist you with setting the audio level. Scroll down to the bottom of the left column and click on the link. 73, Don W3FPR On 10/20/2017 4:54 PM, Bob Cutter wrote: > New to FT8 and KX3 operation. > > I cannot seem to get them communicating. Error message hamlib failure. > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
I get this message whenever I have another program using the
USB<-->Serial port to the KX3. It is most often my logging program. I just quit the logging program, click "Retry" in WSJT-X and everything is OK. 73 Bill AE6JV On 10/20/17 at 2:29 PM, [hidden email] (Don Wilhelm) wrote: >Bob, > >Select the K3 in Hamlib if the KX3 is not present in the selections. >Other than that I cannot help much with the computer end setup. > >FT8 is no different than other soundcard data modes. > >On the KX3 part, set the DATA mode to DATA A. Ignore the >common internet advice for setting the audio and power levels >(and the WSJT-X instructions), and set the KX3 audio level to >indicate 4 bars on the ALC meter with the 5th bar flashing. >Control the power with the power knob. > >There is an article on my website www.w3fpr.com to assist you >with setting the audio level. Scroll down to the bottom of the >left column and click on the link. > >73, >Don W3FPR > >On 10/20/2017 4:54 PM, Bob Cutter wrote: >>New to FT8 and KX3 operation. >> >>I cannot seem to get them communicating. Error message hamlib failure. >> --------------------------------------------------------------------------- Bill Frantz |"After all, if the conventional wisdom was working, the 408-356-8506 | rate of systems being compromised would be going down, www.pwpconsult.com | wouldn't it?" -- Marcus Ranum ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Only one program can control a serial port.
I log to wsjt and then after the session import the ".adi" file into my logger. Use Cortana or other search to locate the ado file. Sent from my iPhone ...nr4c. bill > On Oct 22, 2017, at 4:33 PM, Bill Frantz <[hidden email]> wrote: > > I get this message whenever I have another program using the USB<-->Serial port to the KX3. It is most often my logging program. I just quit the logging program, click "Retry" in WSJT-X and everything is OK. > > 73 Bill AE6JV > >> On 10/20/17 at 2:29 PM, [hidden email] (Don Wilhelm) wrote: >> >> Bob, >> >> Select the K3 in Hamlib if the KX3 is not present in the selections. >> Other than that I cannot help much with the computer end setup. >> >> FT8 is no different than other soundcard data modes. >> >> On the KX3 part, set the DATA mode to DATA A. Ignore the common internet advice for setting the audio and power levels (and the WSJT-X instructions), and set the KX3 audio level to indicate 4 bars on the ALC meter with the 5th bar flashing. Control the power with the power knob. >> >> There is an article on my website www.w3fpr.com to assist you with setting the audio level. Scroll down to the bottom of the left column and click on the link. >> >> 73, >> Don W3FPR >> >>> On 10/20/2017 4:54 PM, Bob Cutter wrote: >>> New to FT8 and KX3 operation. >>> >>> I cannot seem to get them communicating. Error message hamlib failure. >>> > > --------------------------------------------------------------------------- > Bill Frantz |"After all, if the conventional wisdom was working, the > 408-356-8506 | rate of systems being compromised would be going down, > www.pwpconsult.com | wouldn't it?" -- Marcus Ranum > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |