FW: KX1 Question

[Werner & Denise Haschke]

Hi Elliott

Mine has done that all along so I assume it's the norm. All is working fine,
just need the band to open up a bit.
I put the 80-30 mod on mine, also like the paddles even though some say they
don't.
Very sweet little radio.

Werner   N8BB

-----Original Message-----
From: [hidden email]
[mailto:[hidden email]]On Behalf Of Elliott Lawrence
Sent: Friday, May 25, 2007 3:58 PM
To: Elecraft List
Subject: [Elecraft] KX1 Question


I just finished the build of the various KX1 items that I purchased at the
Viasalia DX Convention. All went well at each stage of the build from basic
KX1+KXAT1+KXB30+KXPD1.  I am checking out the total configuration and I
notice something now that I don't recall see earlier.  After I finish
transmitting and the display has shown the 5/6 tick marks their is
approximately a 2-3 second delay of blank screen before the frequency is
shown again!  Is this normal?

Nice little radio but using my TH7 antenna for approximately 10db of gain to
check it out.  Able to work guys even with the poor conditions we are
experiencing.

73
Elliott WA6TLA
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Dick Dickinson]

Hopefully the manual will include a list of necessary tools.


Regards,
Dick - KA5KKT/4

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Eric Swartz - WA6HHQ]

The same as required for the K2.

73, Eric
---

Edward Dickinson III wrote:

> Hopefully the manual will include a list of necessary tools.
>
>
> Regards,
> Dick - KA5KKT/4
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft   
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>
>  

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Ken Kopp]

At one time there was mention of "a Phillips screwdriver" being
the only tool required.

If one needs a list of required tools to go buy 'em in preparation
for the task I wonder if one should be undertaking the task. (:-))
I suppose there "might" be a ham w/o tools ..... naah, doubt it. (:-))

73! Ken Kopp - K0PP
[hidden email]

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Bob Nielsen]

On May 25, 2007, at 4:49 PM, Ken Kopp wrote:

> At one time there was mention of "a Phillips screwdriver" being
> the only tool required.
>
> If one needs a list of required tools to go buy 'em in preparation
> for the task I wonder if one should be undertaking the task. (:-))
> I suppose there "might" be a ham w/o tools ..... naah, doubt it. (:-))
>
> 73! Ken Kopp - K0PP
> [hidden email]
>

Maybe someone about to leave the ranks of the QCAO!

73 - Bob, N7XY

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Eric Swartz - WA6HHQ]

Clarification - LESS tools than required for the K2 :-)

No soldering iron is required at this point and probably just an
assortment of screwdrivers, small pliers, DVM etc.

We'll post a more complete tool list as we get closer to production.

73, Eric
----

Eric Swartz - WA6HHQ, Elecraft wrote:

> The same as required for the K2.
>
> 73, Eric
> ---
>
> Edward Dickinson III wrote:
>> Hopefully the manual will include a list of necessary tools.
>>
>>
>> Regards,
>> Dick - KA5KKT/4
>>
>> _______________________________________________
>> Elecraft mailing list
>> Post to: [hidden email]
>> You must be a subscriber to post to the list.
>> Subscriber Info (Addr. Change, sub, unsub etc.):
>>  http://mailman.qth.net/mailman/listinfo/elecraft   
>> Help: http://mailman.qth.net/subscribers.htm
>> Elecraft web page: http://www.elecraft.com
>>
>>
>>  
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft   
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Hisashi T Fujinaka]

You mean the pry bar necessary to open the cheap ham wallet? :)

On Fri, 25 May 2007, Eric Swartz - WA6HHQ, Elecraft wrote:

> The same as required for the K2.
>
> 73, Eric
> ---
>
> Edward Dickinson III wrote:
>> Hopefully the manual will include a list of necessary tools.
>>
>>
>> Regards,
>> Dick - KA5KKT/4

--
Hisashi T Fujinaka - [hidden email]
BSEE(6/86) + BSChem(3/95) + BAEnglish(8/95) + MSCS(8/03) + $2.50 = latte
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com