Fldigi and K3S

[Carl Yaffey]

Trying to get Fldigi working with my K3S. Had it working fine with my K3.
No problem receiving PSK. But clicking T/R doesn’t start up the transmitter. I’ve tried all sorts of different settings in the rig control, modem, sound card, etc. No luck.
Any suggestions?
73,
Carl Yaffey  K8NU
http://www.carl-yaffey.com
http://www.grassahol.com
http://www.bluesswing.com

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Brian Hunt]

The K3S sound card should show up as a USB CODEC. In FLDIGI under Configure: Soundcard menu select the Audio tab and then Devices. Check PortAudio and make sure both Capture and Playback show USB Audio Codec. I use VOX to trigger transmit and have found I have turn the VOX Gain up from its SSB setting.

Confession: I'm using a USB Soundcard not the K3S but the setup should be the same.

HTH.
73,
Brian, K0DTJ

> On Mar 18, 2017, at 18:12, Carl Yaffey1 <[hidden email]> wrote:
>
> Trying to get Fldigi working with my K3S. Had it working fine with my K3.
> No problem receiving PSK. But clicking T/R doesn’t start up the transmitter. I’ve tried all sorts of different settings in the rig control, modem, sound card, etc. No luck.
> Any suggestions?

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Barry K3NDM]

Carl,
     I just went through a version of that. I had no problem getting
FLDIGI to work with my K3s, but it would not work over N1MM. What I
finally discovered is that I had to go into N1MM's config tab under
hardware and needed to set PTT to on. It makes no sense as I use VOX to
do the same thing and it worked with VOX natively. Until I fixed it, I
had no problem with using MMTTY as my RTTY interface. Now, I can go back
to FLDIGI. There's a bug in there, but I'm not sure whether it's FLDIGI
or N1MM+

73,
Barry
K3NDM



------ Original Message ------
From: "Carl Yaffey1" <[hidden email]>
To: "Elecraft Reflector" <[hidden email]>
Sent: 3/18/2017 9:12:17 PM
Subject: [Elecraft] Fldigi and K3S

>Trying to get Fldigi working with my K3S. Had it working fine with my
>K3.
>No problem receiving PSK. But clicking T/R doesn’t start up the
>transmitter. I’ve tried all sorts of different settings in the rig
>control, modem, sound card, etc. No luck.
>Any suggestions?
>73,
>Carl Yaffey  K8NU
>http://www.carl-yaffey.com
>http://www.grassahol.com
>http://www.bluesswing.com
>
>______________________________________________________________
>Elecraft mailing list
>Home: http://mailman.qth.net/mailman/listinfo/elecraft
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:[hidden email]
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
>Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]