Frequency Display on PX3

[Elecraft mailing list]

I see photos of some PX3 screens where the span width markers (upper left and upper right) are frequencies.  Mine is showing -100.0 and +100.0 for a setting of 200.  I can’t seem to figure out how to change the display to show the frequencies.  I am running the latest firmware version for the PX3, 1.48.  I don’t know what version my hardware is, but the serial number is 1864 from May 2016.

Anyone have any pointers on how to adjust to frequency display?  

Mark Simon
wd9jen    @ aol.com



______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Nr4c]

Check cables. And connectors. Be sure they are plugged in completely.

Sent from my iPhone
...nr4c. bill

> On May 13, 2020, at 9:34 PM, Mark Simon via Elecraft <[hidden email]> wrote:
>
> I see photos of some PX3 screens where the span width markers (upper left and upper right) are frequencies.  Mine is showing -100.0 and +100.0 for a setting of 200.  I can’t seem to figure out how to change the display to show the frequencies.  I am running the latest firmware version for the PX3, 1.48.  I don’t know what version my hardware is, but the serial number is 1864 from May 2016.
>
> Anyone have any pointers on how to adjust to frequency display?  
>
> Mark Simon
> wd9jen    @ aol.com
>
>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Grant Youngman-2]

Toggle Fixer/Tracking mode in the menu.  Of course that will also change the display behavior ...

Grant NQ5T

> On May 13, 2020, at 9:38 PM, Nr4c <[hidden email]> wrote:
>
> Check cables. And connectors. Be sure they are plugged in completely.
>
> Sent from my iPhone
> ...nr4c. bill
>
>
>> On May 13, 2020, at 9:34 PM, Mark Simon via Elecraft <[hidden email]> wrote:
>>
>> I see photos of some PX3 screens where the span width markers (upper left and upper right) are frequencies.  Mine is showing -100.0 and +100.0 for a setting of 200.  I can’t seem to figure out how to change the display to show the frequencies.  I am running the latest firmware version for the PX3, 1.48.  I don’t know what version my hardware is, but the serial number is 1864 from May 2016.
>>
>> Anyone have any pointers on how to adjust to frequency display?  
>>
>> Mark Simon
>> wd9jen    @ aol.com
>>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]