Fw: K3 Tx Eq question

[Richard Fjeld]

I guess I was tired when I wrote this.  My question should simply be; Does the Tx Eq act upon audio from the Line-In jack.  I now suspect so, but would like to verify it.

It has been suggested that I use Data A mode, and the Eq settings will not be used.

Dick, n0ce

----- Original Message -----
From: Richard Fjeld
To: elecraft posting
Sent: Saturday, February 11, 2012 9:31 PM
Subject: K3 Tx Eq question


If the answer to this is in the manual, I didn't see it.

I have been getting into SSTV and I noticed my Rx Eq settings affected the waterfall display (understood). That made me wonder about the Tx Eq settings I use.  The question is: does the Tx Eq have any effect on the audio into the radio on the back panel?  I would think not.??  In other words, is it only acting on the microphone audio.?

For future consideration, it would be nice to have a way to switch off the Eq w/o losing the settings. Not a complaint, just a convenience. Maybe there is, and I haven't learned.

Richard Fjeld, n0ce
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Iain MacDonnell - N6ML-2]

TX EQ is applied to the audio (in phone modes), regardless of the
source of the audio - it even applies to audio stored in the KDVR3....
so yes, it does apply with line-in when in SSB mode.

73,

    ~iain / N6ML



On Mon, Feb 13, 2012 at 2:32 PM, Richard Fjeld <[hidden email]> wrote:

> I guess I was tired when I wrote this.  My question should simply be; Does the Tx Eq act upon audio from the Line-In jack.  I now suspect so, but would like to verify it.
>
> It has been suggested that I use Data A mode, and the Eq settings will not be used.
>
> Dick, n0ce
>
> ----- Original Message -----
> From: Richard Fjeld
> To: elecraft posting
> Sent: Saturday, February 11, 2012 9:31 PM
> Subject: K3 Tx Eq question
>
>
> If the answer to this is in the manual, I didn't see it.
>
> I have been getting into SSTV and I noticed my Rx Eq settings affected the waterfall display (understood). That made me wonder about the Tx Eq settings I use.  The question is: does the Tx Eq have any effect on the audio into the radio on the back panel?  I would think not.??  In other words, is it only acting on the microphone audio.?
>
> For future consideration, it would be nice to have a way to switch off the Eq w/o losing the settings. Not a complaint, just a convenience. Maybe there is, and I haven't learned.
>
> Richard Fjeld, n0ce
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html