Fwd: KAT100-1 Measurements?

[Darrell Bellerive]

Resending this as I have not received any replies yet. Could anyone possibly
help me out?

Thanks!

Darrell

----------  Forwarded Message  ----------

Subject: KAT100-1 Measurements?
Date: July 6, 2006 03:52 pm
From: Darrell Bellerive <[hidden email]>
To: [hidden email]

Would someone be so kind as to take some measurements of the KAT100-1 Antenna
Tuner:

The horizontal distance between the center of the Antenna 1 SO239 connector
(J5) and the center of the Antenna 2 SO239 connector (J6).

The horizontal distance, parallel to the back panel, from the center of the
Antenna 2 SO239 connector (J6) to a projection of the outer edge of the left
side panel. In other words, how far in is the center of the Antenna 2 SO239
connector from the outside edge of the left side panel?

The horizontal distance, parallel to the back panel, between the center of
 the Antenna 1 SO239 connector (J5) and the vertical center line of the
 ground screw (E1).

I am building a new feed-through panel and want to make it line up properly
with a KAT-100-1 which I have not yet purchased. There will be short runs (2
inches or so) of coax between the feed-through panel and the tuner, so the
measurements don't have to be exact. The coax will compensate for a slight
offset.

Thanks in advance!

Darrell   VA7TO   K2#5093

-------------------------------------------------------

--
Darrell Bellerive
Amateur Radio Stations VA7TO and VE7CLA
Grand Forks, British Columbia, Canada
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Darrell Bellerive]

Thanks very much to all who have replied!!!

Here is the average of the measurements for the archive:

On July 23, 2006 03:48 pm, Darrell Bellerive wrote:
>
> Would someone be so kind as to take some measurements of the KAT100-1
> Antenna Tuner:
>
> The horizontal distance between the center of the Antenna 1 SO239 connector
> (J5) and the center of the Antenna 2 SO239 connector (J6).

1.41" +/- 0.03"
Note that this is also the distance from the center of the Antenna 1 SO239
connector (J5) and the center of the Input SO239 connector (J4)

> The horizontal distance, parallel to the back panel, from the center of the
> Antenna 2 SO239 connector (J6) to a projection of the outer edge of the
> left side panel. In other words, how far in is the center of the Antenna 2
> SO239 connector from the outside edge of the left side panel?

To clarify the left panel is the panel as viewed from the front of the
KAT100-1. The measurement does not include the height of the screw heads.
0.83" +/- 0.08"

> The horizontal distance, parallel to the back panel, between the center of
>  the Antenna 1 SO239 connector (J5) and the vertical center line of the
>  ground screw (E1).

2.33" +/- 0.08"
>From the Input SO239 connector (J4): 0.92" +/- 0.08"

The slight error range in measurements will easily be accommodated by the
short coax and ground wire connections of about 1 1/2 to 2 inches in length.
Thanks again and 73,
Darrell   VA7TO   K2#5093

--
Darrell Bellerive
Amateur Radio Stations VA7TO and VE7CLA
Grand Forks, British Columbia, Canada
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com