[Fwd: Re: K3 - RX Problem after latest firmware update]

[Ken Wagner K3IU]

-------- Original Message --------
Subject: Re: [Elecraft] K3 - RX Problem after latest firmware update
Date: Mon, 10 Mar 2008 08:58:47 -0400
From: Ken K3IU <[hidden email]>
To: Stewart Baker <[hidden email]>
CC: AB7R <[hidden email]>, Elecraft Reflector
<[hidden email]>
References: <2008310113356.366831@shack>



Hi Stewart:

I just ran #202 with the latest firmware through your steps several
times and I cannot duplicate your problem. The receiver never goes dead
at any time.

73,
Ken K3IU

Stewart Baker wrote:

> Greg,
> Have re-installed V1.75 & V1.57 again, no change.
>
> Here is a sequence which you might like to try:-
>
> POWER
> 80m LSB 3780
> NORM
> LO CUT=0.15
> SAV ALT1
> NORM
> TX ON/OFF
> ALT1
> TX ON/OFF
> Receive may be dead at this point
>
> If not continue with
> Select USB
> ALT1
> TX ON/OFF
> Receive dead
>
> Switching bands, modes or NORM always restores receiver.
>
> I do (from my point of view) hope that I am not the only one with
> this funny..
>
> 73
> Stewart G3RXQ
>
> On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote:
>  
>> Stewart,
>>
>> Try installing the new firmware again.  I just tried to recreate
>>    
> your report
>  
>> and the radio performs as expected...no problem with RX after a
>>    
> transmit
>  
>> with ALT1 set to 0.15 on the LO side.
>>
>> 73
>> Greg
>> AB7R
>>
>>
>> -----Original Message-----
>> From: [hidden email]
>> [mailto:[hidden email]]On Behalf Of Stewart
>>    
> Baker
>  
>> Sent: Sunday, March 09, 2008 11:32 AM
>> To: Elecraft Reflector
>> Subject: [Elecraft] K3 - RX Problem after latest firmware update
>>
>>
>> I am not sure if there is an obscure problem after the latest
>>    
> MCU
>  
>> and DSP update. Maybe others could check and see if it happens
>>    
> to
>  
>> them ?
>>
>> Any band on SSB if I have the DSP set to ALT1 with the Low Cut
>>    
> set
>  
>> at 0.15 Hz , then after going onto transmit the receiver appears
>> to be dead. If I set the DSP to NORM by pressing the knob the
>> receiver suddenly bursts into life...
>> This happens whether there is any transmit audio or RF out.
>>
>> 73
>> Stewart G3RXQ
>> _______________________________________________
>> Elecraft mailing list
>> Post to: [hidden email]
>> You must be a subscriber to post to the list.
>> Subscriber Info (Addr. Change, sub, unsub etc.):
>> http://mailman.qth.net/mailman/listinfo/elecraft
>>
>> Help: http://mailman.qth.net/subscribers.htm
>> Elecraft web page: http://www.elecraft.com
>> No virus found in this incoming message.
>> Checked by AVG.
>> Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date:
>>    
> 3/9/2008
>  
>> 12:17 PM
>>
>> No virus found in this outgoing message.
>> Checked by AVG.
>> Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date:
>>    
> 3/9/2008
>  
>> 12:17 PM
>>    
>
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft   
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>
>  

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com