HI RFI no power output

classic Classic list List threaded Threaded
4 messages Options
Reply | Threaded
Open this post in threaded view
|

HI RFI no power output

yo2liw
Hello,

I am back with more info after some investigations on my K3/100: No power
output after showing HI RFI message on the screen.
RF indicator at 0. I must mention that I encounter this situation after I
try to work with a homebrew linear amplifier (with tubes)

1. All tests are with 50ohm dummy load.
2. Rig is not on test mode, TX led is flashing
3. TX inhibit OFF
4. RX is fine, no problem
5. Firmware loaded again but no change
6. Check carefully every menu; even load a previous setting when everything
was OK.
7. Remove the KPA3, also disabled from menu, but no power after LPA.
8. Measure components on KANT3, all OK
9. Measure diodes from the switching (KPA3) D7, D8, D9, D10, and all OK.


Could be Q2, Q4, and Q5 from LPA the problem?

I don't have any other idea what to try, I'm very unhappy that this great
rig is not working anymore.

It is very hard from this part of the world the have access to Elecraft
support team (distance, custom, etc) BUT I hope with the help of this
reflector to locate the problem. I know that the Elecraft support reflector
is the best, helping me to fix my K2 when I had problems.

Any help will be highly appreciated!

All the best!

73! Adi
YO2LIW
K3 #791
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Reply | Threaded
Open this post in threaded view
|

Re: HI RFI no power output

yo2liw
Problem fixed. Fortunatelly was an easy fix.

Thank's!

73! Adi

On Mon, Apr 2, 2012 at 7:51 PM, Adi Toplician <[hidden email]> wrote:

> Hello,
>
> I am back with more info after some investigations on my K3/100: No power
> output after showing HI RFI message on the screen.
> RF indicator at 0. I must mention that I encounter this situation after I
> try to work with a homebrew linear amplifier (with tubes)
>
> 1. All tests are with 50ohm dummy load.
> 2. Rig is not on test mode, TX led is flashing
> 3. TX inhibit OFF
> 4. RX is fine, no problem
> 5. Firmware loaded again but no change
> 6. Check carefully every menu; even load a previous setting when
> everything was OK.
> 7. Remove the KPA3, also disabled from menu, but no power after LPA.
> 8. Measure components on KANT3, all OK
> 9. Measure diodes from the switching (KPA3) D7, D8, D9, D10, and all OK.
>
>
> Could be Q2, Q4, and Q5 from LPA the problem?
>
> I don't have any other idea what to try, I'm very unhappy that this great
> rig is not working anymore.
>
> It is very hard from this part of the world the have access to Elecraft
> support team (distance, custom, etc) BUT I hope with the help of this
> reflector to locate the problem. I know that the Elecraft support reflector
> is the best, helping me to fix my K2 when I had problems.
>
> Any help will be highly appreciated!
>
> All the best!
>
> 73! Adi
> YO2LIW
> K3 #791
>
>
>


--
==============
Adrian Toplician
0721 367 850
Timisoara
YO2LIW
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Reply | Threaded
Open this post in threaded view
|

Re: HI RFI no power output

haircutter@verizon.net
In reply to this post by yo2liw
Hello Adi,
What was the problem?

Don...w2xb
Reply | Threaded
Open this post in threaded view
|

Re: HI RFI no power output

KD8NNU
In reply to this post by yo2liw
Ok what was the fix, or did I miss you posting details.

Thanks

~73
Don
KD8NNU


On Fri, Jun 1, 2012 at 4:49 AM, Adi Toplician wrote:

> Problem fixed. Fortunatelly was an easy fix.
>
> Thank's!
>
> 73! Adi
>
> On Mon, Apr 2, 2012 at 7:51 PM, Adi Toplician <[hidden email]>
> wrote:
>
>> Hello,
>>
>> I am back with more info after some investigations on my K3/100: No
>> power
>> output after showing HI RFI message on the screen.
>> RF indicator at 0. I must mention that I encounter this situation
>> after I
>> try to work with a homebrew linear amplifier (with tubes)
>>
>> 1. All tests are with 50ohm dummy load.
>> 2. Rig is not on test mode, TX led is flashing
>> 3. TX inhibit OFF
>> 4. RX is fine, no problem
>> 5. Firmware loaded again but no change
>> 6. Check carefully every menu; even load a previous setting when
>> everything was OK.
>> 7. Remove the KPA3, also disabled from menu, but no power after LPA.
>> 8. Measure components on KANT3, all OK
>> 9. Measure diodes from the switching (KPA3) D7, D8, D9, D10, and all
>> OK.
>>
>>
>> Could be Q2, Q4, and Q5 from LPA the problem?
>>
>> I don't have any other idea what to try, I'm very unhappy that this
>> great
>> rig is not working anymore.
>>
>> It is very hard from this part of the world the have access to
>> Elecraft
>> support team (distance, custom, etc) BUT I hope with the help of this
>> reflector to locate the problem. I know that the Elecraft support
>> reflector
>> is the best, helping me to fix my K2 when I had problems.
>>
>> Any help will be highly appreciated!
>>
>> All the best!
>>
>> 73! Adi
>> YO2LIW
>> K3 #791
>>
>>
>>
>
>
> --
> ==============
> Adrian Toplician
> 0721 367 850
> Timisoara
> YO2LIW
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html