Heil Classic

classic Classic list List threaded Threaded
4 messages Options
Reply | Threaded
Open this post in threaded view
|

Heil Classic

John Glascock (N0IB)
Is it possible to connect a Heil Classic to a KX3?  If so, how?
73,
John
N0IB

KX3 #7432
PX3 #1114

Reply | Threaded
Open this post in threaded view
|

Re: Heil Classic

David Ahrendts
John, I’m sure it is possible. I’ve made an adapter for my Heil Gold Elite microphone (which I love!) for the KX3. This Heil had the Kenwood cable which has a Cat 6 RJ-45 connector which needed an adapter into the three-ring mini-plug. Cost all of $4.75 and about 20-minutes. Hell has a pin list for every microphone on its web site, and the Elecraft folks can give you the pin designation for the mini-plug which, if I remember, is simply element/PTT/ground. The Gold Elite is a hand held with a PTT switch.

David Ahrendts, KC0XT


> On Dec 31, 2014, at 5:48 PM, John Glascock (N0IB) <[hidden email]> wrote:
>
> Is it possible to connect a Heil Classic to a KX3?  If so, how?
>
>
>
> -----
> 73
>
> John (N0IB)
>
>
> --
> View this message in context: http://elecraft.365791.n2.nabble.com/Heil-Classic-tp7596623.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]




David Ahrendts   [hidden email]  




______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
Reply | Threaded
Open this post in threaded view
|

Re: Heil Classic

Jim Brown-10
On Thu,1/1/2015 9:17 AM, David Ahrendts wrote:
> I’m sure it is possible.

Yes. The K3 and KX3 work very well with virtually any decent mic. All
that is needed is a properly wired connector adapter. Just pull out the
documentation for the mic and the K3, see what pins are connected to the
mic on each end, dig out the connectors, pull out your soldering iron,
and make the adapter. I buy ham mic connectors at ham flea markets and
keep a few in the junk box. I buy audio connectors from Full Compass
(near Madison, WI).

If I had to adapt from an RJ45, I would buy a pre-made cable with the
RJ45 connector, cut off the other end, and install the mic connector for
the radio.

73, Jim K9YC
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
Reply | Threaded
Open this post in threaded view
|

Re: Heil Classic

John Glascock (N0IB)
In reply to this post by John Glascock (N0IB)
Thanks

Found a schematic for combining the mike, foot switch, in a project box.
73,
John
N0IB

KX3 #7432
PX3 #1114