Help with download
Locked
 
|
Pressed the wrong button or something! Tx LED flashing but download has
hung. I have switched off the PSU, switched on again and held the Power button down for 30 seconds which I think I had to do once before, but no success. Help please! Chris G3SJJ _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
When you power up the rig, if the red Tx Led is flashing and you see "MCU
LD" in the LCD (it may not be backlit), you should still be able to load firmware into your K3. Just click "Send All Firmware" and the MCU should start to load. The MCU is in "boot load" status if the Red TX led is flashing. Restart the K3 Utility so that it finds the K3 again and again determines its baud rate (which will now be 38,400). Dick, K6KR -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Chris G3SJJ Sent: Thursday, September 11, 2008 1:59 PM To: [hidden email] Subject: [Elecraft] Help with download Pressed the wrong button or something! Tx LED flashing but download has hung. I have switched off the PSU, switched on again and held the Power button down for 30 seconds which I think I had to do once before, but no success. Help please! Chris G3SJJ _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
Sorted. I had Disabled Router Queries on the mHam Router but it still
didn't like it so I changed over a USB / Serial Interface and that worked. My bad. Sorry. Chris G3SJJ Dick Dievendorff wrote: > When you power up the rig, if the red Tx Led is flashing and you see "MCU > LD" in the LCD (it may not be backlit), you should still be able to load > firmware into your K3. Just click "Send All Firmware" and the MCU should > start to load. > > The MCU is in "boot load" status if the Red TX led is flashing. > > Restart the K3 Utility so that it finds the K3 again and again determines > its baud rate (which will now be 38,400). > > Dick, K6KR > > > -----Original Message----- > From: [hidden email] > [mailto:[hidden email]] On Behalf Of Chris G3SJJ > Sent: Thursday, September 11, 2008 1:59 PM > To: [hidden email] > Subject: [Elecraft] Help with download > > Pressed the wrong button or something! Tx LED flashing but download has > hung. I have switched off the PSU, switched on again and held the Power > button down for 30 seconds which I think I had to do once before, but no > success. Help please! > > Chris G3SJJ > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > > > Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
> Sorted. I had Disabled Router Queries on the mHam Router but it still > didn't like it so I changed over a USB / Serial Interface and that > worked. You must also set Radio type = None and have only one port active. 73, ... Joe, W4TV > -----Original Message----- > From: [hidden email] > [mailto:[hidden email]] On Behalf Of Chris G3SJJ > Sent: Thursday, September 11, 2008 6:21 PM > To: Dick Dievendorff > Cc: [hidden email] > Subject: Re: [Elecraft] Help with download > > > Sorted. I had Disabled Router Queries on the mHam Router but it still > didn't like it so I changed over a USB / Serial Interface and that > worked. My bad. Sorry. > Chris G3SJJ > > Dick Dievendorff wrote: > > When you power up the rig, if the red Tx Led is flashing > and you see > > "MCU LD" in the LCD (it may not be backlit), you should > still be able > > to load firmware into your K3. Just click "Send All > Firmware" and the > > MCU should start to load. > > > > The MCU is in "boot load" status if the Red TX led is flashing. > > > > Restart the K3 Utility so that it finds the K3 again and again > > determines its baud rate (which will now be 38,400). > > > > Dick, K6KR > > > > > > -----Original Message----- > > From: [hidden email] > > [mailto:[hidden email]] On Behalf Of Chris G3SJJ > > Sent: Thursday, September 11, 2008 1:59 PM > > To: [hidden email] > > Subject: [Elecraft] Help with download > > > > Pressed the wrong button or something! Tx LED flashing but download > > has > > hung. I have switched off the PSU, switched on again and > held the Power > > button down for 30 seconds which I think I had to do once > before, but no > > success. Help please! > > > > Chris G3SJJ _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |