How to use external ALC with the K3 (applies to the SPE Expert or any other amplifier)

[wayne burdick]

K3 external ALC setup is covered on page 27 of the owner's manual.  
Please read this page before attempting to use external ALC with any  
amplifier.

Executive summary:

1. DO NOT turn the K3's power all the way up and use amplifier ALC to  
maintain peak power at the output of your amplifier. This WILL NOT work.

2. Instead, adjust the power level at the K3 to provide just enough  
drive to hit the peak power desired at the amp. You may want to set  
CONFIG:PWR SET to PER BAND so you don't have to adjust power each time  
you change bands. (This is also covered on page 27.)

3. External ALC is accommodated as a safety backup in the event that  
peak power suddenly increases, etc., due to a failure or load change.  
When properly applied, it will rarely be needed.

Technical details:

The K3 is designed to *not* depend on fast external ALC, because that  
absolutely, positively causes splatter. We studied lab work from  
several authors on this topic and decided to take a different  
approach: our fast ALC is all applied *ahead* of the 1st I.F. crystal  
filter (it's handled by DSP, at the AF and 2nd I.F. stages). We do  
apply slow, long-term ALC after the crystal filter, but this can't  
cause splatter because of the long time constant. External ALC, if  
used, is factored into this part of the equation.

Yes, the K3 is unique in this regard. It may be slightly inconvenient,  
but it will result in a cleaner signal.

73,
Wayne
N6KR

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Ken Kopp-3]

I understand the K3 presently is configured for "positive going"
ALC.  I know there is a mod kit available to change this to a
"negative-going" ALC, and there probably are a number of K3's
that have been changed.

How will the KPA500's ALC be configured?

73! Ken Kopp - K0PP
       [hidden email]


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Doug Faunt N6TQS [phone]]

>From Eric, yesterday:

You will need the mod.

This change was included on All K3s shipped on
Dec 10, 2008 and later. (Rev B KIO3 Digital board)

See: http://www.elecraft.com/K3/k3_app_notes.htm and scroll down to:
"K3 Negative ALC and Ext Band Data Pull-up Mods, Rev B: REMIOUPGD"

73,
Eric WA6HHQ
 ====

(Approx s/n 2362+)

   From: "Ken Kopp" <[hidden email]>
   Date: Thu, 22 Apr 2010 19:43:41 -0000

   I understand the K3 presently is configured for "positive going"
   ALC.  I know there is a mod kit available to change this to a
   "negative-going" ALC, and there probably are a number of K3's
   that have been changed.

   How will the KPA500's ALC be configured?

   73! Ken Kopp - K0PP
          [hidden email]


   ______________________________________________________________
   Elecraft mailing list
   Home: http://mailman.qth.net/mailman/listinfo/elecraft
   Help: http://mailman.qth.net/mmfaq.htm
   Post: mailto:[hidden email]

   This list hosted by: http://www.qsl.net
   Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Bruce Beford-2]

Eric stated yesterday that the K3 ALC mod would be required to use the ALC
on the KPA500:

"You will need the mod.

This change was included on All K3s shipped on Dec 10, 2008 and later.
(Rev B KIO3 Digital board)

See: http://www.elecraft.com/K3/k3_app_notes.htm
and scroll down to:
"K3 Negative ALC and Ext Band Data Pull-up Mods, Rev B:  REMIOUPGD"

73, Eric  WA6HHQ"
====



______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html