Loading... |
Reply to author |
Edit post |
Move post |
Delete this post |
Delete this post and replies |
Change post date |
Print post |
Permalink |
Raw mail |
![]() ![]() ![]() ![]() ![]() ![]() ![]() |
I am almost done assembling #3108. During the 40 meter Transmitter
Alignment (page 72) the radio is drawing 2.2 amps for 10w power. The manual says "much higher than 2 A" is a problem. Is 2.2 a problem? Gordon, KA2NLM _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Loading... |
Reply to author |
Edit post |
Move post |
Delete this post |
Delete this post and replies |
Change post date |
Print post |
Permalink |
Raw mail |
![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Gordon,
2.2 Amps is probably OK - it is only 10% above the nominal, and that is within the range of acceptable tolerance for an assembly of 5% tolerance parts. The power output measurement may be off a bit (especially if you are using an external wattmeter), and if your output is really 11 watts instead of 10, that would readily explain the increased current. How accurate is your dummy load? - if it is not exactly 50 ohms resistive at the frequency you are using, the K2 power ouput indication will not be correct - but OTOH, if the dummy load IS an accurate 50 ohms resistive, the base K2 RF probe type detector is usually more accurate than an external wattmeter. 73, Don W3FPR ----- Original Message ----- I am almost done assembling #3108. During the 40 meter Transmitter Alignment (page 72) the radio is drawing 2.2 amps for 10w power. The manual says "much higher than 2 A" is a problem. Is 2.2 a problem? _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Loading... |
Reply to author |
Edit post |
Move post |
Delete this post |
Delete this post and replies |
Change post date |
Print post |
Permalink |
Raw mail |
![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Gordon:
Also, the current drain depends on your input voltage. With a slightly drained battery showing 11.9 volts on the K2, my current drain on 40M is about 2.2 Amps. At 13.8 volts (showing 13.0 on the K2), it is 2.0. John AA0VE W3FPR - Don Wilhelm wrote: > Gordon, > > 2.2 Amps is probably OK - it is only 10% above the nominal, and that > is within the range of acceptable tolerance for an assembly of 5% > tolerance parts. > > ----- Original Message ----- > I am almost done assembling #3108. During the 40 meter Transmitter > Alignment (page 72) the radio is drawing 2.2 amps for 10w power. The > manual > says "much higher than 2 A" is a problem. Is 2.2 a problem? > > Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Free forum by Nabble | Edit this page |