K2 and kpa 100 (2)

[Elecraft mailing list]

Hello Don, and all ,
So I arrived on page 26 left column down

When the K2 starts up the K2 says: 12.7 Volt I 0.32 amp
I think it's okay?

All values appear OK

un single doubt

For U1 pin 27 I have 5.7
For U1 pin 28 I have 5.58

But I think it's OK, okay?


Thank you for your help

Sorry for vocabulary mistakes I try to explain at best 73 , Christophe F8ACF-56
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Don Wilhelm]

Christophe,

Yes, that is OK.  Voltages within 10% of the value printed in the manual
are normally OK.

73,
Don W3FPR

On 6/29/2017 3:02 PM, Christophe F8ACF-56 via Elecraft wrote:

> Hello Don, and all ,
> So I arrived on page 26 left column down
>
> When the K2 starts up the K2 says: 12.7 Volt I 0.32 amp
> I think it's okay?
>
> All values appear OK
>
> un single doubt
>
> For U1 pin 27 I have 5.7
> For U1 pin 28 I have 5.58
>
> But I think it's OK, okay?
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Elecraft mailing list]

hello don , hello to all ,
I will put everything in the box

I will not have time to work on the KPA100 before mid September

Too much work at the professional level

Thanks again for the help of forum 73 , Christophe F8ACF-56

      De : Don Wilhelm <[hidden email]>
 À : Christophe F8ACF-56 <[hidden email]>; Elecraft Reflector <[hidden email]>
 Envoyé le : Jeudi 29 juin 2017 22h05
 Objet : Re: [Elecraft] K2 and kpa 100 (2)
   
Christophe,

Yes, that is OK.  Voltages within 10% of the value printed in the manual
are normally OK.

73,
Don W3FPR

On 6/29/2017 3:02 PM, Christophe F8ACF-56 via Elecraft wrote:

> Hello Don, and all ,
> So I arrived on page 26 left column down
>
> When the K2 starts up the K2 says: 12.7 Volt I 0.32 amp
> I think it's okay?
>
> All values appear OK
>
> un single doubt
>
> For U1 pin 27 I have 5.7
> For U1 pin 28 I have 5.58
>
> But I think it's OK, okay?
>

   
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]