K3 #3212

[Robert 'RC' Conley]

My K3/10 #3212 is completed. No options were ordered or installed.
Only the 2.7khz filter is installed. I have a couples of issues.
I have done all the test and calibrations on page 65 on the assembly
manual. TWICE.
#1 I do not seem to have power out using SSB even though the W1 Meter says I do.
#2 It would seem that the "AF control"  in k3/10  #3212 for the main
RX (no sub RX) is non functional. Turning the knob has no effect. The
"HI" / "LO" settings in the CONFIG menu does function. In fact the
audio will disappear totally sometimes and the knob must be "wiggled"
to get it back. The RF control works just find in controlling the
volume levels.
Any help will be very much appreciated
72 RC kc5wa

--
72 de RC KC5WA
<http://www.kc5wa.net>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Robert 'RC' Conley]

Review of my earlier post.
# 1... on the MH2 Elecraft microphone. After reading the instruction
sheet that came with the mic problem solved. It pays to RTFM.
# 2... reply from Elecraft Support bad Kaaaanobby. New one on the way....
--
72 de RC KC5WA
<http://www.kc5wa.net>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Steve Ellington]

Huh? What happened to the MH2?
Steve
N4LQ
[hidden email]
----- Original Message -----
From: "Robert 'RC' Conley" <[hidden email]>
To: <[hidden email]>
Sent: Thursday, June 25, 2009 12:18 PM
Subject: Re: [Elecraft] K3 #3212

> Review of my earlier post.
> # 1... on the MH2 Elecraft microphone. After reading the instruction
> sheet that came with the mic problem solved. It pays to RTFM.
> # 2... reply from Elecraft Support bad Kaaaanobby. New one on the way....
> --
> 72 de RC KC5WA
> <http://www.kc5wa.net>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[N5GE]

On Thu, 25 Jun 2009 11:18:29 -0500, "Robert 'RC' Conley"
<[hidden email]> wrote:

>Review of my earlier post.
># 1... on the MH2 Elecraft microphone. After reading the instruction
>sheet that came with the mic problem solved. It pays to RTFM.
># 2... reply from Elecraft Support bad Kaaaanobby. New one on the way....


Yep.  If the setscrew in the knob was tightened too tight the knob
will be cracked and won't rotate the shaft.  I had the same problem on
my factory built #806.

Tom, N5GE

[hidden email]
K3 #806, K3 #1055
XV144, XV432, KRC2
W1 and other small kits.
http://www.n5ge.com

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html