K3 Beta Firmware, Revision 2.31
Locked
12
12
K3 Beta Firmware, Revision 2.31
 
Administrator
|
K3 beta-test firmware revision 2.31 is now available. This is an
extensive update; details appear below. Please send any problem reports to [hidden email]. For instructions on how to load beta firmware, please see: http://www.elecraft.com/K3/k3_software.htm 73, Wayne N6KR * * * MCU 2.31 / DSP 1.89, 8-28-08 New Features and Enhancements: * CW SIDETONE INCREMENTS NOW 10 HZ (originally 50 Hz). * RIT CLR switch now works during transmit in all modes and at any time. * RIT CLR MENU ENTRY: You can use this menu entry to select “UNDO ON” or “UNDO OFF”. OFF is the default. When “ON”, tapping CLR will alternate between 0.00 and the present RIT/XIT offset, if any. * DIVERSITY RECEIVE MODE: If you have the sub receiver (KRX3 option) installed, you can take advantage of “diversity receive” by using two separate receiving antennas. This can improve signal copy during fading, and adds a spatial (L/R) effect to signals. DIVERSITY MODE further enhances this capability by slaving the sub receiver’s mode, filter settings, and VFO to the main receiver. To enter diversity mode, hold SUB until you see “DIVRSTY” on VFO B (about 2 seconds). The kHz decimal point of the VFO A display will flash slowly as a reminder that diversity mode is in effect. Notes on Diversity Mode: 1. Entering diversity mode switches the sub receiver to its AUX antenna source. If you don’t hear any right-channel audio, you probably don’t have an antenna connected to the sub’s AUX input. Refer to the owner’s manual or KRX3 manual for information on sub receiver AUX antenna configuration. 2. If your main and sub receiver have 5-pole crystal filters with differing frequency offsets, you may hear a slow phase modulation in the received audio at some VFO frequencies. The only way to eliminate this effect is to use 5-pole filters with matched offsets (available on request; contact Elecraft) or use 8-pole filters, which have no offset. Miscellaneous changes: * DUAL PB CW MIN CONTEXT BANDWIDTH NOW 400 Hz. In high-QRM situations, a 400 Hz or 500 Hz crystal filter may be very useful as a limit to the context bandwidth. Note that the “pedestal” effect (-24 dB context filter) becomes more of a sloped response as the context bandwidth is reduced. * DATA TX ALC IMPROVEMENTS. PWR control is now more responsive during transmit in all DATA modes. * FM SQUELCH THRESHOLD: Closely matched between main and sub receivers. * NOISE BLANKER ON/OFF ON BAND CHANGE: The DSP noise blanker wasn’t set up properly during band changes. It may have been left ON on the new band in some cases. * PA TEMP and FP TEMP are now "normal" VFO B alternate display modes, meaning that you don’t have to set TECH MD to ON in the config menu. * DDS frequency shifting during T/R changed to eliminate a variation in CW keying duty cycle that was occurring only over specific, narrow frequency ranges on each band. This also eliminated a related CW keying artifact. For software developers: * RG$ command implemented (sub receiver RF gain). * "FA", "UP" ,"DN", “RC”, “RU”, and “RD” COMMANDS UPDATE VFO B IF VFOS ARE LINKED (except in SPLIT). These commands can also be used in transmit mode. --- http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
Excellent. Thank you.
|
Re: K3 Beta Firmware, Revision 2.31
|
|
I have installed the new beta firmware on #980 and am suffering agc
instability. I have returned the agc settings to default and still experience random S meter movements to 30dB over 9 and corresponding lack of audio output. Turning off the agc removes the problem. This is not qrm coming from the antenna because it happens in exactly the same way with the antenna disconnected. I used the latest loader in windows xp. Any ideas please? I have repeated the firmware upgrade and have also binned the file and downloaded a fresh copy. 73 Stephen G4SJP _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Re: K3 Beta Firmware, Revision 2.31
|
|
In reply to this post by wayne burdick
Yes, very good.
We've had ESSB & Diversity implemented. VFO IND next ? 73 Stewart G3RXQ On Thu, 28 Aug 2008 10:42:15 -0700, wayne burdick wrote: > K3 beta-test firmware revision 2.31 is now available. This is an > extensive update; details appear below. Please send any problem reports > to [hidden email]. > > For instructions on how to load beta firmware, please see: > > http://www.elecraft.com/K3/k3_software.htm > > 73, > Wayne > N6KR > > * * * > > MCU 2.31 / DSP 1.89, 8-28-08 > > New Features and Enhancements: > > * CW SIDETONE INCREMENTS NOW 10 HZ (originally 50 Hz). > > * RIT CLR switch now works during transmit in all modes and at > > * RIT CLR MENU ENTRY: You can use this menu entry to select "UNDO ON" or > "UNDO OFF". OFF is the default. When "ON", tapping CLR will alternate > between > 0.00 and the present RIT/XIT offset, if any. > > * DIVERSITY RECEIVE MODE: If you have the sub receiver (KRX3 option) > installed, > you can take advantage of "diversity receive" by using two separate > receiving antennas. > This can improve signal copy during fading, and adds a spatial (L/R) > effect to signals. > DIVERSITY MODE further enhances this capability by slaving the sub > receiver's > mode, filter settings, and VFO to the main receiver. To enter diversity > mode, hold > SUB until you see "DIVRSTY" on VFO B (about 2 seconds). The kHz decimal > point > of the VFO A display will flash slowly as a reminder that diversity > mode is in effect. > > Notes on Diversity Mode: > > 1. Entering diversity mode switches the sub receiver to its AUX antenna > source. If you don't hear any right-channel audio, you probably don't > have > an antenna connected to the sub's AUX input. Refer to the owner's manual > or KRX3 manual for information on sub receiver AUX antenna > configuration. > > 2. If your main and sub receiver have 5-pole crystal filters with > differing frequency > offsets, you may hear a slow phase modulation in the received audio at > some > VFO frequencies. The only way to eliminate this effect is to use 5-pole > filters with > matched offsets (available on request; contact Elecraft) or use 8-pole > filters, > which have no offset. > > Miscellaneous changes: > > * DUAL PB CW MIN CONTEXT BANDWIDTH NOW 400 Hz. In high-QRM situations, > a 400 Hz or 500 Hz crystal filter may be very useful as a limit to the > context bandwidth. > Note that the "pedestal" effect (-24 dB context filter) becomes more of > a sloped > response as the context bandwidth is reduced. > > * DATA TX ALC IMPROVEMENTS. PWR control is now more responsive during > transmit in all DATA modes. > > * FM SQUELCH THRESHOLD: Closely matched between main and sub receivers. > > * NOISE BLANKER ON/OFF ON BAND CHANGE: The DSP noise blanker > wasn't set up properly during band changes. It may have been left ON on > the new > band in some cases. > > * PA TEMP and FP TEMP are now "normal" VFO B alternate display modes, > meaning that you don't have to set TECH MD to ON in the config menu. > > * DDS frequency shifting during T/R changed to eliminate a variation in > CW > keying duty cycle that was occurring only over specific, narrow > frequency ranges > on each band. This also eliminated a related CW keying artifact. > > For software developers: > > * RG$ command implemented (sub receiver RF gain). > > * "FA", "UP" ,"DN", "RC", "RU", and "RD" COMMANDS UPDATE VFO B > VFOS ARE LINKED (except in SPLIT). These commands can also be used > in transmit mode. > > > --- > > http://www.elecraft.com > > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by Stephen Prior
Stephen Prior wrote:
> I have installed the new beta firmware on #980 and am suffering agc > instability. I have returned the agc settings to default and still > experience random S meter movements to 30dB over 9 and corresponding lack > of audio output. Turning off the agc removes the problem. This is not qrm > coming from the antenna because it happens in exactly the same way with the > antenna disconnected. > > I used the latest loader in windows xp. > > Any ideas please? I have repeated the firmware upgrade and have also binned > the file and downloaded a fresh copy. Try checking the box labeled "Send all firmware to K3". If you don't see this, go to View and turn Advanced Mode OFF). Maybe one of the tables didn't get updated properly. -- 73, Vic, K2VCO Fresno CA http://www.qsl.net/k2vco _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Re: K3 Beta Firmware, Revision 2.31
|
|
Hello Vic
Just tried that, and sadly no difference. I'm beginning to get _really_ confused now! Thanks anyway 73 Stephen On 28/08/2008 21:59, "Vic K2VCO" <[hidden email]> wrote: > > Stephen Prior wrote: >> I have installed the new beta firmware on #980 and am suffering agc >> instability. I have returned the agc settings to default and still >> experience random S meter movements to 30dB over 9 and corresponding lack >> of audio output. Turning off the agc removes the problem. This is not qrm >> coming from the antenna because it happens in exactly the same way with the >> antenna disconnected. >> >> I used the latest loader in windows xp. >> >> Any ideas please? I have repeated the firmware upgrade and have also binned >> the file and downloaded a fresh copy. > > Try checking the box labeled "Send all firmware to K3". If you don't see > this, go to View and turn Advanced Mode OFF). > > Maybe one of the tables didn't get updated properly. _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
K3 Beta Firmware, Revision 2.31 E 00000C ERR DSE
|
|
In reply to this post by Stephen Prior
Hi all,
I just upgraded to the latest beta. Set pitch to 630 and then varied the "WIDTH" and SHIFT". Set the WIDTH for 0.80 then when shifting passed FC 0.35, the receiver dies with an error "E 00000C" ERR DSE. It doesn't appear to matter what the "pitch" tone is set. After the error occurs, you must change the SHIFT setting > 0.35 and power off and on. Chris W0ANM _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Re: K3 Beta Firmware, Revision 2.31 E 00000C ERR DSE
|
|
Same firmware here.
Set pitch to 630 Width to .80 Varied shift from lowest setting to highest without issues. There were two loads that needed to be added for this firmware. Did you add the DSP as well as the MCU? David Wilburn K4DGW www.k4dgw.com www.k4rc.net Williamsburg Area Amateur Radio Club (K4RC) My Current LOTW/DXCC/WAS status www.k4dgw.com/WAS.DXCC.info.html Christopher Kovacs wrote: > Hi all, > > I just upgraded to the latest beta. Set pitch to 630 and then varied > the "WIDTH" and SHIFT". Set the WIDTH for 0.80 then when shifting > passed FC 0.35, the receiver dies with an error "E 00000C" ERR DSE. > > It doesn't appear to matter what the "pitch" tone is set. After the > error occurs, you must change the SHIFT setting > 0.35 and power off and > on. > > > Chris W0ANM > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
In reply to this post by wayne burdick
On Thu, 28 Aug 2008 10:42:15 -0700, wayne burdick <[hidden email]> wrote:
>K3 beta-test firmware revision 2.31 is now available. This is an >extensive update; details appear below. Please send any problem reports >to [hidden email]. > >For instructions on how to load beta firmware, please see: > > http://www.elecraft.com/K3/k3_software.htm > >73, >Wayne >N6KR > >* * * > >MCU 2.31 / DSP 1.89, 8-28-08 > >New Features and Enhancements: > >* CW SIDETONE INCREMENTS NOW 10 HZ (originally 50 Hz). > Yahooo! Excellent! Now I can set the pitch exactly for these old ears and work CW without the hearing aids :O) Thank you, thank you, thank you, Tom, N5GE - SWOT 3537 - Grid EM12jq "Those who would give up Essential Liberty to purchase a little Temporary Safety deserve neither Liberty nor Safety" An excerpt from a letter written in 1755 from the Assembly to the Governor of Pennsylvania. Support the entire Constitution, not just the parts you like. http://www.n5ge.com http://www.eQSL.cc/Member.cfm?N5GE _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Amateur Radio Operator N5GE
|
Re: K3 Beta Firmware, Revision 2.31 E 00000C ERR DSE
|
|
In reply to this post by dave.wilburn
Looks like it was my mistake.... I could have swore that the DSP was
being loaded the first time. I went back to the previous firmware and then reloaded the latest beta firmware making sure that I send "all". It's good now. Chris w0anm David Wilburn wrote: > Same firmware here. > > Set pitch to 630 > > Width to .80 > > Varied shift from lowest setting to highest without issues. > > There were two loads that needed to be added for this firmware. Did > you add the DSP as well as the MCU? > > David Wilburn > K4DGW > www.k4dgw.com > www.k4rc.net > Williamsburg Area Amateur Radio Club (K4RC) > > My Current LOTW/DXCC/WAS status > www.k4dgw.com/WAS.DXCC.info.html > > > > Christopher Kovacs wrote: >> Hi all, >> >> I just upgraded to the latest beta. Set pitch to 630 and then varied >> the "WIDTH" and SHIFT". Set the WIDTH for 0.80 then when shifting >> passed FC 0.35, the receiver dies with an error "E 00000C" ERR DSE. >> >> It doesn't appear to matter what the "pitch" tone is set. After the >> error occurs, you must change the SHIFT setting > 0.35 and power off >> and on. >> >> >> Chris W0ANM >> _______________________________________________ >> Elecraft mailing list >> Post to: [hidden email] >> You must be a subscriber to post to the list. >> Subscriber Info (Addr. Change, sub, unsub etc.): >> http://mailman.qth.net/mailman/listinfo/elecraft Help: >> http://mailman.qth.net/subscribers.htm >> Elecraft web page: http://www.elecraft.com >> > _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Re: K3 Beta Firmware, Revision 2.31
|
Administrator
|
In reply to this post by N5GE
Tom Childers, N5GE wrote:
>> * CW SIDETONE INCREMENTS NOW 10 HZ (originally 50 Hz). >> > [snip] > > Yahooo! > > Excellent! Now I can set the pitch exactly for these old ears and > work CW > without the hearing aids :O) > > Thank you, thank you, thank you,.... You're welcome, Tom. What else can we design for you today? :) 73, Wayne N6KR --- http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Re: Re: K3 Beta Firmware, Revision 2.31
|
|
>You're welcome, Tom. What else can we design for you today? :) The 1.5 kW amplifier? 73, Hank, W6SX Mammoth Lakes, California Elevation 8083 feet in John Muir's Range of Light _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
RE: Re: K3 Beta Firmware, Revision 2.31
|
|
How about the 800w?
72, Bill K9YEQ K2 #35, K2 # 5279, KX1 #35, Mini Modules, etc. -----Original Message----- From: [hidden email] [mailto:[hidden email]] On Behalf Of Hank Garretson Sent: Thursday, August 28, 2008 8:31 PM To: wayne burdick Cc: Elecraft Reflector Subject: Re: [Elecraft] Re: K3 Beta Firmware, Revision 2.31 >You're welcome, Tom. What else can we design for you today? :) The 1.5 kW amplifier? 73, Hank, W6SX Mammoth Lakes, California Elevation 8083 feet in John Muir's Range of Light _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Re: K3 Beta Firmware, Revision 2.31 E 00000C ERR DSE
|
|
In reply to this post by Christopher Kovacs
Awesome, glad to hear it is up and running.
David Wilburn K4DGW www.k4dgw.com Christopher Kovacs wrote: > Looks like it was my mistake.... I could have swore that the DSP was > being loaded the first time. I went back to the previous firmware and > then reloaded the latest beta firmware making sure that I send "all". > > It's good now. > > Chris w0anm > > David Wilburn wrote: >> Same firmware here. >> >> Set pitch to 630 >> >> Width to .80 >> >> Varied shift from lowest setting to highest without issues. >> >> There were two loads that needed to be added for this firmware. Did >> you add the DSP as well as the MCU? >> >> David Wilburn >> K4DGW >> www.k4dgw.com >> www.k4rc.net >> Williamsburg Area Amateur Radio Club (K4RC) >> >> My Current LOTW/DXCC/WAS status >> www.k4dgw.com/WAS.DXCC.info.html >> >> >> >> Christopher Kovacs wrote: >>> Hi all, >>> >>> I just upgraded to the latest beta. Set pitch to 630 and then varied >>> the "WIDTH" and SHIFT". Set the WIDTH for 0.80 then when shifting >>> passed FC 0.35, the receiver dies with an error "E 00000C" ERR DSE. >>> >>> It doesn't appear to matter what the "pitch" tone is set. After the >>> error occurs, you must change the SHIFT setting > 0.35 and power off >>> and on. >>> >>> >>> Chris W0ANM >>> _______________________________________________ >>> Elecraft mailing list >>> Post to: [hidden email] >>> You must be a subscriber to post to the list. >>> Subscriber Info (Addr. Change, sub, unsub etc.): >>> http://mailman.qth.net/mailman/listinfo/elecraft Help: >>> http://mailman.qth.net/subscribers.htm >>> Elecraft web page: http://www.elecraft.com >>> >> > > Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Re: K3 Beta Firmware, Revision 2.31
|
In reply to this post by wayne burdick
Tom,
Ask for a remote Low Power antenna tuner that will work with the K2 and K3 ;o) Cheers, Julius n2wn
Julius Fazekas
N2WN Tennessee Contest Group http://www.k4ro.net/tcg/index.html Tennessee QSO Party http://www.tnqp.org/ Elecraft K2 #4455 Elecraft K3/100 #366 Elecraft K3/100 |
|
|
In reply to this post by wayne burdick
> You're welcome, Tom. What else can we design for you today? :)
Just a couple of thoughts... 1) How about enabling the firmware for the KTCXO3-1 TCXO, so that those of us who paid for that capability can actually use it? 2) How about concentrating on creating a rock-solid code base, with the AGC/NR/NB/whatever all functioning at their best possible level of performance. 73, Steve NN4X _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
----- Original Message -----
From: "S Sacco" <[hidden email]> > > 2) How about concentrating on creating a rock-solid code base, with > the AGC/NR/NB/whatever all functioning at their best possible level of > performance. > > 73, > Steve NN4X And make CW sound good with NR turned on. 73 Hank K8DD ____________________________________________________________ Receive Notifications of Incoming Messages Easily monitor multiple email accounts & access them with a click. Visit http://www.inbox.com/notifier and check it out! _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by Julius Fazekas n2wn
YES! We need a remote version of the KAT100. That would help improve a lot of signals. 73, Henry - K4TMC K3/100 #98 K2/100 #3137 -----Original Message----- From: Julius Fazekas n2wn <[hidden email]> To: [hidden email] Sent: Fri, 29 Aug 2008 10:16 am Subject: Re: [Elecraft] K3 Beta Firmware, Revision 2.31 Tom, Ask for a remote Low Power antenna tuner that will work with the K2 and K3 ;o) Cheers, Julius n2wn wayne burdick wrote: > > Tom Childers, N5GE wrote: > >>> * CW SIDETONE INCREMENTS NOW 10 HZ (originally 50 Hz). >>> >> [snip] >> >> Yahooo! >> >> Excellent! Now I can set the pitch exactly for these old ears and >> work CW >> without the hearing aids :O) >> >> Thank you, thank you, thank you,.... > > You're welcome, Tom. What else can we design for you today? :) > > 73, > Wayne > N6KR > > --- > > http://www.elecraft.com > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > > -- View this message in context: http://n2.nabble.com/K3-Beta-Firmware%2C-Revision-2.31-tp790252p792301.html Sent from the Elecraft mailing list archive at Nabble.com. _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
I will vote for the remote antenna tuner and a Syllabic Squelch.
A syllabic voice squelch would be a nice feature to have on the K3. Most commercial HF radios have these voice activated squelch circuits. They seem to ignore and noise and static very well on SSB. Craig --- On Fri, 8/29/08, [hidden email] <[hidden email]> wrote: > From: [hidden email] <[hidden email]> > Subject: Re: [Elecraft] K3 Beta Firmware, Revision 2.31 - Remote ATU > To: [hidden email], [hidden email] > Date: Friday, August 29, 2008, 10:30 PM > YES! We need a remote version of the KAT100. That would > help improve > a lot of signals. > > 73, > Henry - K4TMC > K3/100 #98 > K2/100 #3137 > > -----Original Message----- > From: Julius Fazekas n2wn <[hidden email]> > To: [hidden email] > Sent: Fri, 29 Aug 2008 10:16 am > Subject: Re: [Elecraft] K3 Beta Firmware, Revision 2.31 > > Tom, > > Ask for a remote Low Power antenna tuner that will work > with the K2 and > K3 > ;o) > > Cheers, > Julius > n2wn > > > wayne burdick wrote: > > > > Tom Childers, N5GE wrote: > > > >>> * CW SIDETONE INCREMENTS NOW 10 HZ (originally > 50 Hz). > >>> > >> [snip] > >> > >> Yahooo! > >> > >> Excellent! Now I can set the pitch exactly for > these old ears and > >> work CW > >> without the hearing aids :O) > >> > >> Thank you, thank you, thank you,.... > > > > You're welcome, Tom. What else can we design for > you today? :) > > > > 73, > > Wayne > > N6KR > > > > --- > > > > http://www.elecraft.com > > > > _______________________________________________ > > Elecraft mailing list > > Post to: [hidden email] > > You must be a subscriber to post to the list. > > Subscriber Info (Addr. Change, sub, unsub etc.): > > http://mailman.qth.net/mailman/listinfo/elecraft > > > > Help: http://mailman.qth.net/subscribers.htm > > Elecraft web page: http://www.elecraft.com > > > > > > -- > View this message in context: > http://n2.nabble.com/K3-Beta-Firmware%2C-Revision-2.31-tp790252p792301.html > Sent from the Elecraft mailing list archive at Nabble.com. > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > > > > > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
KAT100 (was: Re: K3 Beta Firmware, Revision 2.31 - Remote ATU)
|
|
In reply to this post by k4tmc
I'd like to use this opportunity to say that I'm impressed by the
KAT100. Everything I've been able to tune with my manual MFJ-949, the KAT100 will also tune. Jon LA4RT [hidden email] wrote: > > YES! We need a remote version of the KAT100. That would help improve a > lot of signals. > > 73, > Henry - K4TMC > K3/100 #98 > K2/100 #3137 _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |