K3 Configuration Reset

[JayR]

Is there a simple way to reset all the configuration parameters to the factory defaults
with out going through each item?

Jay

[Gill W4RYW]

JayR wrote

Is there a simple way to reset all the configuration parameters to the factory defaults
with out going through each item?

Jay

You can reset everything by the following:

Power off
Hold in shift knob while pressing power on switch unit it fully powers up

You will have to start over again just like you had just finished building it - so don't so this just for grins.

If you have an older configuration file saved you can reload it and be right back where you were when you saved the file. The firmware is not affected either way - kinda like a restore point in Win XP.

Good luck!

Gill

[JayR]

Perhaps I stated the question incorrectly.
Is there a list of the factory default parameters
in the configuration, so that one can compare the default
to the present setting.

Jay


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Don Wilhelm-4]

Jay,

Yes, it is easier than a list.  Enter the menu and tap the DISP button -
the default setting will be displayed in the VFO B area.

73,
Don W3FPR

Jay Rodaman wrote:
> Perhaps I stated the question incorrectly.
> Is there a list of the factory default parameters
> in the configuration, so that one can compare the default
> to the present setting.
>
> Jay
>  
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Ken Wagner K3IU]

When in the CONFIG mode, simply tap the DISP button and you will see the
"Default" value for the selected parameter. It is also in the manual for
each parameter.
73,
Ken K3IU
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
On 12/23/2009 9:29 PM, Jay Rodaman wrote:
> Perhaps I stated the question incorrectly.
> Is there a list of the factory default parameters
> in the configuration, so that one can compare the default
> to the present setting.
>
> Jay
>    
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Mike Harris]

G'day,

Yes, both within the radio and in the handbook "Menu Functions".
Sadly reading the handbook to find out how to use the radio and how
to connect it to the outside world is a minority pastime.

Regards,

Mike VP8NO


----- Original Message -----
From: "Jay Rodaman" <[hidden email]>
To: "'Gill W4RYW'" <[hidden email]>;
<[hidden email]>
Sent: Wednesday, December 23, 2009 11:29 PM
Subject: Re: [Elecraft] K3 Configuration Reset


> Perhaps I stated the question incorrectly.
> Is there a list of the factory default parameters
> in the configuration, so that one can compare the default
> to the present setting.
>
> Jay

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html