Elecraft

K3 Firmware

Classic

List

Threaded

6 messages Options

Rudi-2

K3 Firmware

Dear FM,

The upload for the new firmware makes me crazy.

I get error after te DSP 02.81 version.

2 errors:

ERR DSE
ERR PL1

I noticed that the menu has strange letters but this is due to the fault
upload from de DSP firmware.

I tried different pc and have the latest version of the USB adapter.

All info is welcome.

73 - Rudi - ON7CL

PS: The upload from the new firmware for my KX3 was succesfull.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Don Wilhelm-4

Re: K3 Firmware

Rudi,

Did you look at the chart of error codes in the back of the manual and
tried the correction steps given for that error? That is the first step.

For ERR DSE, the correction is to reload the DSP firmware. If you tried
that and obtained the same error, download a new copy of the firmware
from Elecraft and try again.

73,
Don W3FPR

On 10/14/2013 3:43 AM, Rudi wrote:

> Dear FM,
>
> The upload for the new firmware makes me crazy.
>
> I get error after te DSP 02.81 version.
>
> 2 errors:
>
> ERR DSE
> ERR PL1
>
> I noticed that the menu has strange letters but this is due to the fault
> upload from de DSP firmware.
>
> I tried different pc and have the latest version of the USB adapter.
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Keith Heimbold

Re: K3 Firmware

Rudi,

I had similar issue running the firmware upgrade through my MicroHam microkeyer USB router. I am not sure if you are running your cable direct or through another system with virtual comports. Virtual comports seem to have issue with the firmware for the K3.

I didn't see if you mentioned anything but a direct connection but I thought I would bring up my similar experience.

Keith

Sent from my iPhone please excuse typos

> On Oct 14, 2013, at 6:05 AM, "Don Wilhelm" <[hidden email]> wrote:
>
> Rudi,
>
> Did you look at the chart of error codes in the back of the manual and tried the correction steps given for that error? That is the first step.
>
> For ERR DSE, the correction is to reload the DSP firmware. If you tried that and obtained the same error, download a new copy of the firmware from Elecraft and try again.
>
> 73,
> Don W3FPR
>
>> On 10/14/2013 3:43 AM, Rudi wrote:
>> Dear FM,
>>
>> The upload for the new firmware makes me crazy.
>>
>> I get error after te DSP 02.81 version.
>>
>> 2 errors:
>>
>> ERR DSE
>> ERR PL1
>>
>> I noticed that the menu has strange letters but this is due to the fault
>> upload from de DSP firmware.
>>
>> I tried different pc and have the latest version of the USB adapter.
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

Joe Subich, W4TV-4

Re: K3 Firmware

> I had similar issue running the firmware upgrade through my MicroHam
> microkeyer USB router.

Never perform a firmware upload to *any* rig with a microHAM interface.
Every microHAM Users Manual specifically states the interfaces are not
to be used for firmware uploads. There are several reasons for this -
some rigs require direct manipulation of RTS and/or DTR to control the
upload process and microHAM does not support that or in the case of the
K3, the radio resets itself in the middle of the upload process which
causes a reset of the communications data parameters.

> Virtual comports seem to have issue with the firmware for the K3.

Like many other "RS-232" control ports, the K3 does not like signaling
voltages much less than +/-10V. Many newer USB to serial adapters are
being designed for "low power" operation which typically means +/- 8,
5 or even 3.3V signal levels. Measure the voltage on each of the
pins of your USB to serial adapter and make sure it is not a "low power"
device.

73,

... Joe, W4TV

On 10/14/2013 9:27 AM, Keith Heimbold wrote:

> Rudi,
>
> I had similar issue running the firmware upgrade through my MicroHam microkeyer USB router. I am not sure if you are running your cable direct or through another system with virtual comports. Virtual comports seem to have issue with the firmware for the K3.
>
> I didn't see if you mentioned anything but a direct connection but I thought I would bring up my similar experience.
>
> Keith
>
> Sent from my iPhone please excuse typos
>
>> On Oct 14, 2013, at 6:05 AM, "Don Wilhelm" <[hidden email]> wrote:
>>
>> Rudi,
>>
>> Did you look at the chart of error codes in the back of the manual and tried the correction steps given for that error? That is the first step.
>>
>> For ERR DSE, the correction is to reload the DSP firmware. If you tried that and obtained the same error, download a new copy of the firmware from Elecraft and try again.
>>
>> 73,
>> Don W3FPR
>>
>>> On 10/14/2013 3:43 AM, Rudi wrote:
>>> Dear FM,
>>>
>>> The upload for the new firmware makes me crazy.
>>>
>>> I get error after te DSP 02.81 version.
>>>
>>> 2 errors:
>>>
>>> ERR DSE
>>> ERR PL1
>>>
>>> I noticed that the menu has strange letters but this is due to the fault
>>> upload from de DSP firmware.
>>>
>>> I tried different pc and have the latest version of the USB adapter.
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:[hidden email]
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>

KV5J

Re: K3 Firmware

In reply to this post by Rudi-2

Speaking of K3 firmware. It's been 6 months since the last update. Does that mean the K3 is a mature product and all the wish list items that can be included are done? I don't have a list so I'm not sure if anything is missing.

Keith

'DGB'

FS W2 Wattmeter

In reply to this post by Joe Subich, W4TV-4

Excellent condition, about 1-1/2 yr. old, no longer needed, non-smoking
environment, original owner. It was a kit that I assembled, looks and
works as new. With manual, coupler (2KW, 1.8 - 54mhz), rs-232-3.5mm
connecting cable and power cable.

Will ship in original packing and insure Priority Mail for $195.00 in
the US ... Paypal or USPS money order. Tnx ... Dwight NS9I
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html