K3 - MCU 2.16 vs. 2.19 NR Volume Level

[W6NEK]

Hello all K3'ers,
While running MCU 2.16 (DSP 184) the Noise Reduction (NR) signal audio level was a very close balance between NR OFF and NR ON.  However after downloading MCU 2.19 (DSP 187) I find the NR signal volume level significantly reduced when NR is ON.  Anyone else notice this??

I reloaded MCU 2.16 (DSP 184) and now NR signal volume level is once again balanced between NR ON and NR OFF.

Frank - W6NEK

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[David Pratt]

In a recent message, W6NEK <[hidden email]> wrote ...
>While running MCU 2.16 (DSP 184) the Noise Reduction (NR) signal audio
>level was a very close balance between NR OFF and NR ON.  However after
>downloading MCU 2.19 (DSP 187) I find the NR signal volume level
>significantly reduced when NR is ON.  Anyone else notice this??

Yes, Frank, I find exactly the same as you.

73
--
David G4DMP
Leeds, England, UK
------


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Geoffrey Downs-2]

Me too.

Geoff
G3UCK

----- Original Message -----
From: "David Pratt" <[hidden email]>
To: "Elecraft Reflector" <[hidden email]>
Sent: Wednesday, July 23, 2008 5:26 PM
Subject: Re: [Elecraft] K3 - MCU 2.16 vs. 2.19 NR Volume Level

> In a recent message, W6NEK <[hidden email]> wrote ...
>>While running MCU 2.16 (DSP 184) the Noise Reduction (NR) signal audio
>>level was a very close balance between NR OFF and NR ON.  However after
>>downloading MCU 2.19 (DSP 187) I find the NR signal volume level
>>significantly reduced when NR is ON.  Anyone else notice this??
>
> Yes, Frank, I find exactly the same as you.
>
> 73
> --
> David G4DMP
> Leeds, England, UK

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Guy, K2AV]

Same here.

73, Guy
K2AV

Geoffrey Downs-2 wrote

Me too.

Geoff
G3UCK

----- Original Message -----
From: "David Pratt" <[e-mail]>
To: "Elecraft Reflector" <[e-mail]>
Sent: Wednesday, July 23, 2008 5:26 PM
Subject: Re: [Elecraft] K3 - MCU 2.16 vs. 2.19 NR Volume Level


> In a recent message, W6NEK <[e-mail]> wrote ...
>>While running MCU 2.16 (DSP 184) the Noise Reduction (NR) signal audio
>>level was a very close balance between NR OFF and NR ON.  However after
>>downloading MCU 2.19 (DSP 187) I find the NR signal volume level
>>significantly reduced when NR is ON.  Anyone else notice this??
>
> Yes, Frank, I find exactly the same as you.
>
> 73
> --
> David G4DMP
> Leeds, England, UK

_______________________________________________
Elecraft mailing list
Post to: [e-mail]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com