K3 Signalink and WSPR
Locked
 
|
Just finished performing the various modifications to make the Signalink USB a much better unit. I've got it all hooked back up and I can TX/RX with it. I.e. I can hear audio and when I tune using WSPR into my dummy load my wattmeter shows output. However when in TX mode the TX audio also plays through the K3's speaker with no volume control. How do I turn this off? I've been searching Google and KE7X's book but I'm not coming up with the right terms to find that pesky setting.
AC2EV - Don ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Don,
It sounds as though you have MON turned up - You can't turn it off with any switch, but you can set it to zero. 73, Don W3FPR On 4/19/2015 3:57 PM, Ac2ev wrote: > Just finished performing the various modifications to make the Signalink USB a much better unit. I've got it all hooked back up and I can TX/RX with it. I.e. I can hear audio and when I tune using WSPR into my dummy load my wattmeter shows output. However when in TX mode the TX audio also plays through the K3's speaker with no volume control. How do I turn this off? I've been searching Google and KE7X's book but I'm not coming up with the right terms to find that pesky setting. > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Thanks to WM3M and W3FPR. I completely overlooked that setting. Was busy in the config searching for it.
AC2EV - Don > On Apr 19, 2015, at 16:06, Don Wilhelm <[hidden email]> wrote: > > Don, > > It sounds as though you have MON turned up - You can't turn it off with any switch, but you can set it to zero. > > 73, > Don W3FPR > >> On 4/19/2015 3:57 PM, Ac2ev wrote: >> Just finished performing the various modifications to make the Signalink USB a much better unit. I've got it all hooked back up and I can TX/RX with it. I.e. I can hear audio and when I tune using WSPR into my dummy load my wattmeter shows output. However when in TX mode the TX audio also plays through the K3's speaker with no volume control. How do I turn this off? I've been searching Google and KE7X's book but I'm not coming up with the right terms to find that pesky setting. > Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
In reply to this post by ac2ev
Hi Don,
I am running digital with no interface, using the K3 itself as the interface. Seems to work very well with no issues of any kind so far. I am NOT a lover of Signalink devices... I have a friend across the small valley we live in from me, maybe 1/2 miles away... The Signalink craps up the spectrum... I have another friend, who lives 100 yards from me, who does NOT use anything, and a K3, and he creates issues only when I am less than 7 KHz from him. As an aside, I did a small test using his signal, I took a snapshot using the P3 prior to replacing the Synths, and one after, with exactly the same settings on his and my rigs, there is significantly less area under the curve after the synth swap. -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net for MixW support see; http://groups.yahoo.com/neo/groups/mixw/info for Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info for MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Sun, 2015-04-19 at 15:57 -0400, Ac2ev wrote: > Just finished performing the various modifications to make the Signalink USB a much better unit. I've got it all hooked back up and I can TX/RX with it. I.e. I can hear audio and when I tune using WSPR into my dummy load my wattmeter shows output. However when in TX mode the TX audio also plays through the K3's speaker with no volume control. How do I turn this off? I've been searching Google and KE7X's book but I'm not coming up with the right terms to find that pesky setting. > > AC2EV - Don > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |