K3 Speaker Audio Quit
Locked
 
|
Well, this is a strange one. Last week my trusty old Yamaha CM500 cans finally got so deteriorated I got tired of picking small pieces of black rubber out of my ears so I looked for a replacement. Bought a Koss SB45 that I used for 15 minutes and quit because they hurt. Today I got a brand new CM500 delivered and hooked it up.
What I got was nice audio in the headphones, but nothing to the speaker. I have SPEAKERS set to 2 for diversity RX. When I set SPKR + PH = yes I get audio to the headphones, but nothing to the internal speaker. When SPKR + PH is set to NO, I get nothing. Unplugging the CM500 cable makes no difference. What the heck did I do to cause this? I hope it is something simple/stupid! Any ideas? Jim / W6JHB ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Jim,
Check this, you could have bumped the "1" button! line"> <IF THE SPEAKER IS NOT WORKING with headphones unplugged: Locate the CONFIG:SPKR+PH menu entry. Tap ‘1’ on the numeric keypad until you see PH.R SW– . The minus sign (-)indicates inverted switch logic for the jack for the newer KIO3 audio board. Exit the menu and re-save your configuration using K3 Utility. -- Carl AB1DD Resistance is futile. (don't know about reactance, though) ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
Re: K3 Speaker Audio Quit
|
|
Carl - gave it a try but didn’t help. Each push of the “1” button changes it from - to + and I hear a short noise from the internal speaker, but still no audio getting through.
> On Jan 13, 2019, at 4:33 PM, Carl <[hidden email]> wrote: > > Jim, > > Check this, you could have bumped the "1" button! > > > line"> <IF THE SPEAKER IS NOT WORKING with headphones unplugged: Locate the CONFIG:SPKR+PH menu > entry. Tap ‘1’ on the numeric keypad until you see PH.R SW– . The minus sign (-)indicates inverted switch > logic for the jack for the newer KIO3 audio board. Exit the menu and re-save your configuration using K3 Utility. > > -- > Carl > AB1DD > Resistance is futile. > (don't know about reactance, though) > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
Re: K3 Speaker Audio Quit - RESOLVED!
|
|
In reply to this post by Elecraft mailing list
Got fixed!!! Reseated the plugs and all working fine now.
Thanks for everyone’s assistance! Jim / W6JHB > On Jan 13, 2019, at 6:11 PM, Brian Hunt <[hidden email]> wrote: > > I take it that you are plugging the CM500 into the rear jacks. Make sure you have the headphones plug in the headphones jack and not the speakers jack. Yes, they are separate and right next to each other. Don't ask me how I know this. :-) > > If you are using the internal speaker you want SPKRS set to 1. Stereo will appear in the headphones anyway. GL > > Brian, K0DTJ > >> On Jan 13, 2019, at 16:27, James Bennett via Elecraft <[hidden email] <mailto:[hidden email]>> wrote: >> >> Well, this is a strange one. Last week my trusty old Yamaha CM500 cans finally got so deteriorated I got tired of picking small pieces of black rubber out of my ears so I looked for a replacement. Bought a Koss SB45 that I used for 15 minutes and quit because they hurt. Today I got a brand new CM500 delivered and hooked it up. >> >> What I got was nice audio in the headphones, but nothing to the speaker. I have SPEAKERS set to 2 for diversity RX. When I set SPKR + PH = yes I get audio to the headphones, but nothing to the internal speaker. When SPKR + PH is set to NO, I get nothing. Unplugging the CM500 cable makes no difference. >> >> What the heck did I do to cause this? I hope it is something simple/stupid! Any ideas? >> >> Jim / W6JHB >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[hidden email] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [hidden email] <mailto:[hidden email]> Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |