K3 config menu problem

[Juha - oh6os]

Hello everybody,

My K3 config menu has got mixed up!

For example: I tried set LIN OUT, so upper line show OFF. That is just for previous entry LCD TST.

My first and second entries are somelike "2212222" and upper lines like "0.00" and "trn 1". After these all is ok to CW PADL "tip=dot". Then there is CW WGHT "On"? After that every entries has wrong upper line!

73 de juha - oh6os
K3 2100

[Brendan Minish]

Juha

Reload the Front panel firmware using the K3 utility and see if this
clears it up

On Mon, 2010-10-18 at 02:58 -0700, Juha - oh6os wrote:

> Hello everybody,
>
> My K3 config menu has got mixed up!
>
> For example: I tried set LIN OUT, so upper line show OFF. That is just for
> previous entry LCD TST.
>
> My first and second entries are somelike "2212222" and upper lines like
> "0.00" and "trn 1". After these all is ok to CW PADL "tip=dot". Then there
> is CW WGHT "On"? After that every entries has wrong upper line!
>
> 73 de juha - oh6os
> K3 2100

--
73
Brendan EI6IZ

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Juha - oh6os]

I have all new firmware. No help.

juha

2010/10/18 Brendan Minish <[hidden email]>

> Juha
>
> Reload the Front panel firmware using the K3 utility and see if this
> clears it up
>
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Jim AB3CV]

I've seen this recently on my K3 when connected to my new battery operated
laptop via a new FTDI-based KUSB. Once I connected power to the laptop and
did an EEInit on the K3 all menus resumed their normal appearance.

good luck

jim ab3cv

On Mon, Oct 18, 2010 at 10:02 AM, Juha Kasari <[hidden email]> wrote:

> I have all new firmware. No help.
>
> juha
>
> 2010/10/18 Brendan Minish <[hidden email]>
>
> > Juha
> >
> > Reload the Front panel firmware using the K3 utility and see if this
> > clears it up
> >
> >
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[wayne burdick]

Juha,

You probably have the wrong revision of the "FPF" firmware file  
loaded. When you load firmware, be sure to load all files, including  
FPF.

73,
Wayne
N6KR

On Oct 18, 2010, at 2:58 AM, Juha - oh6os wrote:

>
> Hello everybody,
>
> My K3 config menu has got mixed up!
>
> For example: I tried set LIN OUT, so upper line show OFF. That is  
> just for
> previous entry LCD TST.
>
> My first and second entries are somelike "2212222" and upper lines  
> like
> "0.00" and "trn 1". After these all is ok to CW PADL "tip=dot". Then  
> there
> is CW WGHT "On"? After that every entries has wrong upper line!
>
> 73 de juha - oh6os
> K3 2100
> --
> View this message in context: http://elecraft.365791.n2.nabble.com/K3-config-menu-problem-tp5646447p5646447.html
> Sent from the [K3] mailing list archive at Nabble.com.
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Juha - oh6os]

I did EEInit, but no help.

juha

2010/10/18 Jim Miller <[hidden email]>

> I've seen this recently on my K3 when connected to my new battery operated
> laptop via a new FTDI-based KUSB. Once I connected power to the laptop and
> did an EEInit on the K3 all menus resumed their normal appearance.
>
> good luck
>
> jim ab3cv
>
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Juha - oh6os]

Hello,

I have now

MCU  04.12
FPF   01.09
DSP1 02.58

I used "Send All Firmware to K3". Is these ok?

juha

2010/10/18 Wayne Burdick <[hidden email]>

> Juha,
>
> You probably have the wrong revision of the "FPF" firmware file loaded.
> When you load firmware, be sure to load all files, including FPF.
>
> 73,
> Wayne
> N6KR
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dick Dievendorff]

Current production firmware is

MCU 04.12
FPF 01.13
DSP 02.60

On the firmware tab of the K3 Utility, check the "copy new files from
Elecraft into local folder" and click "check versions now".
This should fetch the current firmware into your computer.  Then press "Send
All Firmware".

Dick, K6KR


-----Original Message-----
From: [hidden email]
[mailto:[hidden email]] On Behalf Of Juha Kasari
Sent: Monday, October 18, 2010 8:12 AM
To: Wayne Burdick
Cc: [hidden email]
Subject: Re: [Elecraft] K3 config menu problem

Hello,

I have now

MCU  04.12
FPF   01.09
DSP1 02.58

I used "Send All Firmware to K3". Is these ok?

juha

2010/10/18 Wayne Burdick <[hidden email]>

> Juha,
>
> You probably have the wrong revision of the "FPF" firmware file loaded.
> When you load firmware, be sure to load all files, including FPF.
>
> 73,
> Wayne
> N6KR
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Juha - oh6os]

Tnx.

I did like you said just before I read your message ;).

Now config menu Is OK!!!!

Thank you everybody for helping.

juha

2010/10/18 Dick Dievendorff <[hidden email]>

> Current production firmware is
>
> MCU 04.12
> FPF 01.13
> DSP 02.60
>
> On the firmware tab of the K3 Utility, check the "copy new files from
> Elecraft into local folder" and click "check versions now".
> This should fetch the current firmware into your computer.  Then press
> "Send
> All Firmware".
>
> Dick, K6KR
>
>
> -----Original Message-----
> From: [hidden email]
> [mailto:[hidden email]] On Behalf Of Juha Kasari
> Sent: Monday, October 18, 2010 8:12 AM
> To: Wayne Burdick
> Cc: [hidden email]
> Subject: Re: [Elecraft] K3 config menu problem
>
> Hello,
>
> I have now
>
> MCU  04.12
> FPF   01.09
> DSP1 02.58
>
> I used "Send All Firmware to K3". Is these ok?
>
> juha
>
> 2010/10/18 Wayne Burdick <[hidden email]>
>
> > Juha,
> >
> > You probably have the wrong revision of the "FPF" firmware file loaded.
> > When you load firmware, be sure to load all files, including FPF.
> >
> > 73,
> > Wayne
> > N6KR
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html