K3 data mode fail

[W5GAI]

While using my K3 in data A mode with wsjt-x software on 6M, TX stopped,
and other data modes also have no TX output. RX remains OK, and CW and SSB
TX & RX still work OK.
  Need suggestions on diagnosis or reset process. Direct replies off list
are OK. Thanks, Skip W5GAI
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Jim Brown-10]

On 6/30/2019 8:43 PM, Skip Cameron wrote:
> Need suggestions on diagnosis or reset process.

VOX settings?  Level changes?  Windoze updates screwing with sound card
settings or choices?

73, Jim K9YC


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[k2te]

Skip,

Check your soundcard cable to your Line-in jack.  I had the same problem
occur several times before I discovered the problem was the cable.  I
pressed on it at the line in jack while testing and the power out came
back up.  Same symptoms: no output, RX signals OK, CW and SSB OK.
Replaced the cable and everything FB now.

73 de Ed

____________________________________________________________
Sad News For Meghan Markle And Prince Harry
track.volutrk.com
http://thirdpartyoffers.juno.com/TGL3141/5d19eb71cd8946b712651st03vuc
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Don Wilhelm]

Skip,

Make certain the K3 is getting audio into the Line In jack.
Pull the speaker or Line Out cable from your soundcard and plug
headphones or amplified computer speakers into that soundcard jack.
Then do a TX from your software application.  Do you hear any audio
tones?  If not, check the computer/soundcard.

If audio there, plug in the cable to the K3 Line In making sure the
plugs are fully seated on each end.  You could have a bad cable.
Since you have good audio to the computer on RX, swap the two audio
cables between the soundcard and the K3.  If you have an OK waterfall
display, the cable between K3 Line Out and soundcard line in (mic) is
working.

If you still have problems, contact [hidden email] for further
analysis.

73,
Don W3FPR

On 6/30/2019 11:43 PM, Skip Cameron wrote:
> While using my K3 in data A mode with wsjt-x software on 6M, TX stopped,
> and other data modes also have no TX output. RX remains OK, and CW and SSB
> TX & RX still work OK.
>    Need suggestions on diagnosis or reset process. Direct replies off list
> are OK. Thanks, Skip W5GAI
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]