K3 firmware rev. 3.62: Improved PTT control of DVR message playback

classic Classic list List threaded Threaded
2 messages Options
Reply | Threaded
Open this post in threaded view
|

K3 firmware rev. 3.62: Improved PTT control of DVR message playback

Eric Swartz - WA6HHQ
Administrator
K3 beta-test firmware revision 3.62 (with DSP rev. 2.46) is now
available. See release notes below.

Please send any questions to [hidden email]. For instructions
on how to load beta firmware, see:

      http://www.elecraft.com/K3/k3_software.htm

73,
Wayne
N6KR

* * *

MCU 3.63, 11-20-2009

* PTT USE WITH DVR: If the KDVR3 menu entry ‘1’ tap option
is set to AUTOPTT (the default), then PTT behaves as follows:

   - If you start DVR message play first (by tapping M1-M4), then
     assert PTT during the message, DVR play will be canceled.

   - If you assert PTT first, then play a DVR message, it will
     play normally, and will complete even if you let go of PTT.

You can also cancel DVR message play by tapping REC, as usual,
whether PTT is asserted or not. (Or cancel from a computer
using the “RX;” command – see below.)

Note: If the KDVR3 menu entry ‘1’ tap option is set to
USE PTT, then PTT is required as a qualifier for DVR
message play. In this case, releasing PTT in the middle
of a DVR message will cancel it.

Remote Control Command Changes:

* DVR MSG PLAY CANCEL: You can now use the “RX”
command to cleanly cancel DVR message play (as well
as any other transmit or message-play function, in any mode).

* CONFIG:DIGOUT1 MENU PARAMETER is now accessible
with the “MP" command. Values 000 and 001 only; get/set.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Reply | Threaded
Open this post in threaded view
|

Firmware Request

Elliott Lawrence-3
Boy the firmware changes keep coming and coming even before I can load the
previous beta a new one arrives.

I would like to make a firmware change request.  Several times while in the
Data A mode I have accidently hit the M1 button where I have a voice message
of my call stored.  Of course before I can stop it my call is sent on the
RTTY frequency out of band!!!  Not a good thing.

Please consider updating the software to inhibit the voice message or only
use a CW message previously stored when in the Data Mode.  Actually having
the CW message played in Data Mode would be good in a pile up as you could
send your call without using the paddle and actually complete the QSO with
only using the M buttons!!

vy 73,
Elliott WA6TLA

----- Original Message -----
From: "Eric Swartz - WA6HHQ, Elecraft" <[hidden email]>
To: "Elecraft List" <[hidden email]>
Sent: Friday, November 20, 2009 7:12 PM
Subject: [Elecraft] K3 firmware rev. 3.62: Improved PTT control of
DVRmessage playback


K3 beta-test firmware revision 3.62 (with DSP rev. 2.46) is now
available. See release notes below.

Please send any questions to [hidden email]. For instructions
on how to load beta firmware, see:

      http://www.elecraft.com/K3/k3_software.htm

73,
Wayne
N6KR


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html