K3, noise from com cable on SSB?
Locked
K3, noise from com cable on SSB?
 
|
A new to me low SN# K3..no problems on CW. Noise blanker now works!
I "think" all the SSB settings are ok. I run SO2R with a YCCC SO2R+ box, so audio gets routed through a laptop, then out to the so2r box, then to one of 2 rigs. When on SSB I hear a moderately loud feedback-ISB noise w/ an added pulsing noise in my earphones (monitor) (and also outgoing on the air). It's probably equal to about 25w or 25% of my outgoing sound. No good. I initially thought it was my cheapie antique unshielded FTDI based serial to USB adapter, as it had LED's which flashed to the exact pulse I was hearing, so I replaced it with a brand new FTDI based cable. Same sound. If I plug a mic directly into the radio, no problems. Another radio on my same (SO2R) setup has no noise on the audio, so do I have something not set right in the rig, or what's going on with my com port? Thanks for any insight. Mike VE9AA Mike, Coreen & Corey Keswick Ridge, NB ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
I can't seem to find anything in the manual about this but I presume
there is some driver needed to use the USP port for audio as well as CAT/PTT? Ken ------------------------------------------------------------------------------ President and CTO - Arcom Communications Makers of repeater controllers and accessories. http://www.arcomcontrollers.com/ Authorized Dealers for Kenwood and Telewave and we offer complete repeater packages! AH6LE/R - IRLP Node 3000 http://www.irlp.net "We don't just make 'em. We use 'em!" ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
In reply to this post by Mike Smith VE9AA
Well if you look at the sound devices you should see a USB CODEK as a record/playback device. That's it.
Sent from my iPhone ...nr4c. bill > On May 20, 2016, at 7:29 PM, Ken Arck <[hidden email]> wrote: > > I can't seem to find anything in the manual about this but I presume there is some driver needed to use the USP port for audio as well as CAT/PTT? > > Ken > ------------------------------------------------------------------------------ > President and CTO - Arcom Communications > Makers of repeater controllers and accessories. > http://www.arcomcontrollers.com/ > Authorized Dealers for Kenwood and Telewave and > we offer complete repeater packages! > AH6LE/R - IRLP Node 3000 > http://www.irlp.net > "We don't just make 'em. We use 'em!" > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Thanks to everyone who responded.
As I already had the USB Codecs installed for a Yaesu radio, I thought maybe there were different ones for the K3. I'll do some playing, thanks Ken At 06:19 PM 5/20/2016, Nr4c wrote: >Well if you look at the sound devices you should see a USB CODEK as >a record/playback device. That's it. > >Sent from my iPhone >...nr4c. bill > > > > On May 20, 2016, at 7:29 PM, Ken Arck <[hidden email]> wrote: > > > > I can't seem to find anything in the manual about this but I > presume there is some driver needed to use the USP port for audio > as well as CAT/PTT? > > > > Ken > > > ------------------------------------------------------------------------------ > > President and CTO - Arcom Communications > > Makers of repeater controllers and accessories. > > http://www.arcomcontrollers.com/ > > Authorized Dealers for Kenwood and Telewave and > > we offer complete repeater packages! > > AH6LE/R - IRLP Node 3000 > > http://www.irlp.net > > "We don't just make 'em. We use 'em!" > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[hidden email] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [hidden email] ------------------------------------------------------------------------------ President and CTO - Arcom Communications Makers of repeater controllers and accessories. http://www.arcomcontrollers.com/ Authorized Dealers for Kenwood and Telewave and we offer complete repeater packages! AH6LE/R - IRLP Node 3000 http://www.irlp.net "We don't just make 'em. We use 'em!" ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
In reply to this post by Nr4c
Well.. PTT is working fine as is the CODEC from radio to computer (in
my case, WSJT). But for the life of me, I cannot get anything but digital noise from computer to radio. I'm not exactly a neophyte here but I cannot get this to work (and yes, I've selected the USB Speaker CODEC for driving the radio) Win 10 on a 64 bit, 3.5 gHz machine.... Ken At 07:00 PM 5/20/2016, Ken Arck wrote: >Thanks to everyone who responded. > >As I already had the USB Codecs installed for a Yaesu radio, I >thought maybe there were different ones for the K3. I'll do some >playing, thanks > >Ken > > >At 06:19 PM 5/20/2016, Nr4c wrote: >>Well if you look at the sound devices you should see a USB CODEK as >>a record/playback device. That's it. >> >>Sent from my iPhone >>...nr4c. bill >> >> >> > On May 20, 2016, at 7:29 PM, Ken Arck <[hidden email]> wrote: >> > >> > I can't seem to find anything in the manual about this but I >> presume there is some driver needed to use the USP port for audio >> as well as CAT/PTT? >> > >> > Ken >> > >> ------------------------------------------------------------------------------ >> > President and CTO - Arcom Communications >> > Makers of repeater controllers and accessories. >> > http://www.arcomcontrollers.com/ >> > Authorized Dealers for Kenwood and Telewave and >> > we offer complete repeater packages! >> > AH6LE/R - IRLP Node 3000 >> > http://www.irlp.net >> > "We don't just make 'em. We use 'em!" >> > >> > ______________________________________________________________ >> > Elecraft mailing list >> > Home: http://mailman.qth.net/mailman/listinfo/elecraft >> > Help: http://mailman.qth.net/mmfaq.htm >> > Post: mailto:[hidden email] >> > >> > This list hosted by: http://www.qsl.net >> > Please help support this email list: http://www.qsl.net/donate.html >> > Message delivered to [hidden email] > >------------------------------------------------------------------------------ >President and CTO - Arcom Communications >Makers of repeater controllers and accessories. >http://www.arcomcontrollers.com/ >Authorized Dealers for Kenwood and Telewave and >we offer complete repeater packages! >AH6LE/R - IRLP Node 3000 >http://www.irlp.net >"We don't just make 'em. We use 'em!" > >______________________________________________________________ >Elecraft mailing list >Home: http://mailman.qth.net/mailman/listinfo/elecraft >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:[hidden email] > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html >Message delivered to [hidden email] ------------------------------------------------------------------------------ President and CTO - Arcom Communications Makers of repeater controllers and accessories. http://www.arcomcontrollers.com/ Authorized Dealers for Kenwood and Telewave and we offer complete repeater packages! AH6LE/R - IRLP Node 3000 http://www.irlp.net "We don't just make 'em. We use 'em!" ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
In reply to this post by Nr4c
Well..it seems the only way for the USB audio from computer > radio
to work is for radio to be in DATA mode.....Duh...... Thanks to all who responded Ken ------------------------------------------------------------------------------ President and CTO - Arcom Communications Makers of repeater controllers and accessories. http://www.arcomcontrollers.com/ Authorized Dealers for Kenwood and Telewave and we offer complete repeater packages! AH6LE/R - IRLP Node 3000 http://www.irlp.net "We don't just make 'em. We use 'em!" ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
Re: [RESOLVED] Audio via USB for the K3S?
|
|
In reply to this post by Nr4c
You definitely do NOT need to be in data mode. I've never switched to data
and do PSK31 every day on a K3S. "LINE" level set high enough (mine is around 10-13) "MIC SEL" set to LINE IN. You'll also need to make sure the USB Codec sound input/output levels are set on your computer to levels that work. Start with each slider mid way to get into the ballpark and adjust from there. There's a way to do both front mic and line in (internal sound card) but I would pick up my keyboard with the mic. A couple of macros later and I have a button for phone and a button for digital that changes settings appropriately. -Bob N3XKB On Sat, May 21, 2016 at 10:09 AM, Ken Arck <[hidden email]> wrote: > Well..it seems the only way for the USB audio from computer > radio to > work is for radio to be in DATA mode.....Duh...... > > Thanks to all who responded > > > > Ken > > ------------------------------------------------------------------------------ > President and CTO - Arcom Communications > Makers of repeater controllers and accessories. > http://www.arcomcontrollers.com/ > Authorized Dealers for Kenwood and Telewave and > we offer complete repeater packages! > AH6LE/R - IRLP Node 3000 > http://www.irlp.net > "We don't just make 'em. We use 'em!" > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [hidden email] > Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
Re: [RESOLVED] Audio via USB for the K3S?
|
|
On Sun, May 22, 2016 at 7:26 PM, Bob Darlington <[hidden email]>
wrote: > You definitely do NOT need to be in data mode. I've never switched to > data... > ============ Correct. You can transmit and receive data just fine in SSB mode. It's good that you fixed your problem, but that wasn't it. Tony KT0NY ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |