K3
Locked
 
|
Does K3 have a variable delay (0-50ms) to control older amps TX relays (ie; SB-220, L4B, etc)?
What is voltage/current limit to control TX amp relays (ie; SB-220, L4B, etc)? If using an external receiver with K3 is the RX ANT OUT the correct connection to get signal to the external RX? I see a PHONES connector on rear panel. If used how does one switch between speaker and headphones? I like the idea to get MIC and HEADPHONES off the front panel. Is the PA circuit breaker readily available if needed? Can ANT1 and ANT2 be set and stored by band? _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
> If using an external receiver with K3 is the RX ANT OUT the correct connection to get signal to the external RX?
Yes. > I see a PHONES connector on rear panel. If used how does one switch between speaker and headphones? I like the idea to get MIC and HEADPHONES off the front panel. Plug in headphones to either the front or rear phones jack and the speaker is muted. > Is the PA circuit breaker readily available if needed? Yes, it is on the rear panel, part of the fan assembly. > Can ANT1 and ANT2 be set and stored by band? Yes. 73, Lyle KK7P (I'll let someone else answer the first two questions you asked.) _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
Administrator
|
Lyle Johnson wrote:
>> Can ANT1 and ANT2 be set and stored by band? The settings for ANT1 and 2 are stored on a per-band, per-GP-memory basis. Also stored is up to a 5-character text label for each antenna. So, when you change antennas, it'll tell you whether you're on the "YAGI" or the "VERT", etc. The antenna name is also flashed briefly whenever you change bands, as a quick reminder that's more meaningful than just "1" or "2". 73, Wayne N6KR --- http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by KK7P
I hope (and expect) that the K3 has more
robust headphone jacks. 73, Bob N6WG ----- Original Message ----- From: "Lyle Johnson" <[hidden email]> To: <[hidden email]> Cc: "ELECRAFT" <[hidden email]> Sent: Friday, May 04, 2007 5:17 PM Subject: Re: [Elecraft] K3 > > If using an external receiver with K3 is the RX ANT OUT the correct connection to get signal to the external RX? > > Yes. > > > I see a PHONES connector on rear panel. If used how does one switch between speaker and headphones? I like the idea to get MIC and HEADPHONES off the front panel. > > Plug in headphones to either the front or rear phones jack and the > speaker is muted. > > > Is the PA circuit breaker readily available if needed? > > Yes, it is on the rear panel, part of the fan assembly. > > > Can ANT1 and ANT2 be set and stored by band? > > Yes. > > 73, > > Lyle KK7P > > (I'll let someone else answer the first two questions you asked.) > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
In reply to this post by wayne burdick
Now that is COOL!
73, Bob N6WG ----- Original Message ----- From: "wayne burdick" <[hidden email]> To: "Elecraft Reflector" <[hidden email]> Cc: <[hidden email]> Sent: Friday, May 04, 2007 5:28 PM Subject: [Elecraft] Re: K3 > Lyle Johnson wrote: > > >> Can ANT1 and ANT2 be set and stored by band? > > The settings for ANT1 and 2 are stored on a per-band, per-GP-memory > basis. > > Also stored is up to a 5-character text label for each antenna. So, > when you change antennas, it'll tell you whether you're on the "YAGI" > or the "VERT", etc. The antenna name is also flashed briefly whenever > you change bands, as a quick reminder that's more meaningful than just > "1" or "2". > > 73, > Wayne > N6KR > > --- > > http://www.elecraft.com > > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
Administrator
|
In reply to this post by n7ka
[hidden email] wrote:
> Does K3 have a variable delay (0-50ms) to control older amps TX relays > (ie; SB-220, L4B, etc)? Yes. It also has a separate PTT input jack, so you can pre-switch the amp using a footswitch, etc. > > What is voltage/current limit to control TX amp relays (ie; SB-220, > L4B, etc)? The keying device is rated at 200 volts, 6 amps. > > If using an external receiver with K3 is the RX ANT OUT the correct > connection to get signal to the external RX? If you have an external receiver connected to RX ANT OUT, it will get RF from the K3's main antenna jack *if* you turn RX ANT on (K3 front panel switch). This is very useful, because it allows you to A/B test the K3 against a second receiver at the tap of a switch. 73, Wayne N6KR --- http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |