K3 utility program

[VE3WDM]

Good evening all
I am about to set the K3 up using the K3 utility program. To configure the filters of which I have the Stock  2.7 khz 5 pole crystal filter, inrad 500 400 and 250 filters. Does the utility take you through all the steps that are in the manual on page 46 (bandwidth, frequency offset and transmit crystal selection) or do I have to go back and forth from the k3 utility to the manual for complete filter setup?
Mike
VE3WDM
     
_________________________________________________________________
Windows Live: Make it easier for your friends to see what you’re up to on Facebook.
http://go.microsoft.com/?linkid=9691816
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Iain MacDonnell - N6ML-2]

On Sat, Dec 12, 2009 at 2:20 AM, Mike Weir <[hidden email]> wrote:
>
> Good evening all
> I am about to set the K3 up using the K3 utility program. To configure the filters of which I have the Stock  2.7 khz 5 pole crystal filter, inrad 500 400 and 250 filters. Does the utility take you through all the steps that are in the manual on page 46 (bandwidth, frequency offset and transmit crystal selection) or do I have to go back and forth from the k3 utility to the manual for complete filter setup?

Not really sure what you mean by "go back and forth...", but the K3
Utility presents a form where you specify all of the filter parameters
for the filters in either the main or sub receiver, then submit it to
the K3. It's quite straightforward.

    ~Iain / N6ML
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dick Dievendorff]

The K3 Utility filter configuration dialog helps you to completely set  
up filter bandwidth, offset, gain, rx filter select by mode, and Tx  
filter select by mode. There is a screen shot in K3 Utility Help that  
shows this.

Dick, K6KR


Sent from my iPhone

On Dec 11, 2009, at 4:20 PM, Mike Weir <[hidden email]> wrote:

>
> Good evening all
> I am about to set the K3 up using the K3 utility program. To  
> configure the filters of which I have the Stock  2.7 khz 5 pole  
> crystal filter, inrad 500 400 and 250 filters. Does the utility take  
> you through all the steps that are in the manual on page 46  
> (bandwidth, frequency offset and transmit crystal selection) or do I  
> have to go back and forth from the k3 utility to the manual for  
> complete filter setup?
> Mike
> VE3WDM
>
> _________________________________________________________________
> Windows Live: Make it easier for your friends to see what you’re up  
> to on Facebook.
> http://go.microsoft.com/?linkid=9691816
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html