K3S RIT Problem

[stengrevics]

I seem to be reading signals about 800 Hz high.

I have cleared RIT.   I suspect I have hit some other setting by mistake.

Any suggestions would be appreciated.

73,

John
WA1EAZ
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft mailing list]

 Is your REF CAL adjusted correctly?




    On Wednesday, April 3, 2019, 8:48:58 PM EDT, John Stengrevics <[hidden email]> wrote:  
 
 I seem to be reading signals about 800 Hz high.

I have cleared RIT.  I suspect I have hit some other setting by mistake.

Any suggestions would be appreciated.

73,

John
WA1EAZ
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
 
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Bob McGraw - K4TAX]

Just to check, I suggest going to WWV at 10 MHZ and in CW mode and press
SPOT.  That will automatically lock to the WWV carrier and your selected
sidetone frequency.   No audio or zero beating needed.    If indeed your
radio is off 800 Hz then the SPOT function will not bring it in and
lock.   If it is 100 Hz or less usually SPOT will bring it in.   When it
locks it will show the frequency and you can then know exactly what the
error is referenced to WWV.    Should be able to have an accuracy of +/-
1 Hz using this method.   If it is greater than this, I suggest tweaking
your REF CAL value a few Hz up or down as needed.

73

Bob, K4TAX


On 4/3/2019 9:24 PM, Harry Yingst via Elecraft wrote:

>   Is your REF CAL adjusted correctly?
>
>
>
>
>      On Wednesday, April 3, 2019, 8:48:58 PM EDT, John Stengrevics <[hidden email]> wrote:
>  
>   I seem to be reading signals about 800 Hz high.
>
> I have cleared RIT.  I suspect I have hit some other setting by mistake.
>
> Any suggestions would be appreciated.
>
> 73,
>
> John
> WA1EAZ
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>    
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html