KAT100 & KPA100 for sale

[Patrick Taylor-2]

As I wait for my K3 I would like to sell my KPA100 (with all upgrades
including the replacement of C-31) and my KAT100-2 both in an EC-2
enclosure. These are together in the EC-2 and are connected to and
communicate with the K2 through the aux bus cable. Your K2 must have a KIO2
for this combination to work.

 

Initial cost of the KPA-100, KAT100-2 and EC-2 was $667 I will sell for $550
including shipping anywhere in the CONUS.

 

Please communicate off-list to [hidden email]

 

73

 

Pat Taylor,  W3HVG

K2 #503,  K3 ?


No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.516 / Virus Database: 269.19.2/1224 - Release Date: 1/14/2008
5:39 PM
 

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[DW Holtman]

Hello,

While waiting on my K3, I decided to order and put together a K1. The whole
procedure went great. The receiver worked great and the alignment went
smooth. After I installed the transmitter parts, there is no receive. First
I'm going to check for wrong parts, cold solder joint etc.  Looking at the
schematic drawings, the receive signal path goes through D10, D11  and D12
which were all installed during the transmitter parts installation section.

Does anyone have any other suggestions/ideas?

Best,
DW Holtman
WB7SSN


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[DW Holtman]

Hello,

Found the problem, as I strongly suspected, it was a mistake on my part. On
page 42 it says to install a "100 uH choke at RFC2 and RFC5". I did not read
the complete sentence and only installed the choke at RFC2.

Thanks for the help.

Best,
DW Holtnan
WB7SSN

----- Original Message -----
From: "DW Holtman" <[hidden email]>
To: <[hidden email]>
Sent: Wednesday, January 16, 2008 8:22 AM
Subject: [Elecraft] K1 trouble shooting question

> Hello,
>
> While waiting on my K3, I decided to order and put together a K1. The
> whole procedure went great. The receiver worked great and the alignment
> went smooth. After I installed the transmitter parts, there is no receive.
> First I'm going to check for wrong parts, cold solder joint etc.  Looking
> at the schematic drawings, the receive signal path goes through D10, D11
> and D12 which were all installed during the transmitter parts installation
> section.
>
> Does anyone have any other suggestions/ideas?
>
> Best,
> DW Holtman
> WB7SSN
>
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com 

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[crstrode]

 What other "spare parts" do you have left after building your new K1?

My K1 (#2476) seems to be running A-OK.   However, there is a bunch of stuff leftover, including a 100K resistor - sure would like to know what that darned resistor is for!


Carl Strode
WA7CS

WB7SSN wrote:


Found the problem, as I strongly suspected, it was a mistake on my part. On page 42 it says to install a "100 uH choke at RFC2 and RFC5". I did not read the complete sentence and only installed the choke at RFC2.

--
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com