I have KPA500 s/n 3835 which I purchased along with a KAT500, factory
assembled, last Summer. It soon died and was subsequently returned to Elecraft at the beginning of August for service, and several parts were replaced. One part was missing. The unit was received back from Elecraft at the end of August and has worked flawlessly since that time. They extended the warranty to cover the initial defects (thank you, Elecraft!). Today, after operating a few hours, I stepped out of the shack for a couple hours and returned to find the unit was shut off. Everything else in the shack was still on and operating (computers, exciter rig, etc.). It was impossible to power on, so I removed the fuse block and checked. Both fuses check OK with DMM (I am operating on 115 VAC so fuses are 12a). There is power thru the power cable. I can't access any fault information since I cannot power it up. I don't seem to have a schematic nor can I find one online to check for other fuses, etc. (Anybody have one, or a link?) Suggestions? If possible I would like to avoid the lengthy shipping / service delay and $100+ cost of UPS to return it yet again. Of course I am hoping it is something that can be field serviced. Elecraft Service has been notified, but it is still early in 6-land. Thanks! 73 Lyn, W0LEN ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
You should call tech to fix get resolved. Nothing this reflector can do for you.
Bill K9YEQ Have a great day! Bill ________________________________ From: [hidden email] <[hidden email]> on behalf of Lyn Norstad <[hidden email]> Sent: Tuesday, February 25, 2020 8:50:12 AM To: Elecraft Reflector <[hidden email]> Subject: [Elecraft] KPA500 dead again I have KPA500 s/n 3835 which I purchased along with a KAT500, factory assembled, last Summer. It soon died and was subsequently returned to Elecraft at the beginning of August for service, and several parts were replaced. One part was missing. The unit was received back from Elecraft at the end of August and has worked flawlessly since that time. They extended the warranty to cover the initial defects (thank you, Elecraft!). Today, after operating a few hours, I stepped out of the shack for a couple hours and returned to find the unit was shut off. Everything else in the shack was still on and operating (computers, exciter rig, etc.). It was impossible to power on, so I removed the fuse block and checked. Both fuses check OK with DMM (I am operating on 115 VAC so fuses are 12a). There is power thru the power cable. I can't access any fault information since I cannot power it up. I don't seem to have a schematic nor can I find one online to check for other fuses, etc. (Anybody have one, or a link?) Suggestions? If possible I would like to avoid the lengthy shipping / service delay and $100+ cost of UPS to return it yet again. Of course I am hoping it is something that can be field serviced. Elecraft Service has been notified, but it is still early in 6-land. Thanks! 73 Lyn, W0LEN ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
Free forum by Nabble | Edit this page |