KPA500

[k6dgw]

I'm revamping my wooden rack that used to hold a bunch of things, most
of which are gone now.  I need some design info.

Is the form factor for the yet to be available KPA500 the same as my K3?

73,

Fred K6DGW
- Northern California Contest Club
- CU in the 2010 Cal QSO Party 2-3 Oct 2010
- www.cqp.org
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[KK7P]

  Yes, except the fan on the rear is a bit deeper than the twin fans on
the K3/100.

73,

Lyle KK7P

  Is the form factor for the yet to be available KPA500 the same as my K3?

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Phillip Lontz]

The KPA 500?
Will I need to upgrade to the 100 watt machine or will the ten watt k3 do the job.

Phil
Santa Fe, NM

Sent from my iPad

On Sep 8, 2010, at 6:58 PM, Lyle Johnson <[hidden email]> wrote:

>  Yes, except the fan on the rear is a bit deeper than the twin fans on
> the K3/100.
>
> 73,
>
> Lyle KK7P
>
>  Is the form factor for the yet to be available KPA500 the same as my K3?
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Robert Friess]

The KPA500 requires 30 to 40 watts for full output.  With 10 watts of drive
the output will be around 200 watts or a little less.

Bob, N6CM



On Wed, Sep 8, 2010 at 8:15 PM, Phil Townsend <[hidden email]> wrote:

> The KPA 500?
> Will I need to upgrade to the 100 watt machine or will the ten watt k3 do
> the job.
>
> Phil
> Santa Fe, NM
>
> Sent from my iPad
>
> On Sep 8, 2010, at 6:58 PM, Lyle Johnson <[hidden email]> wrote:
>
> >  Yes, except the fan on the rear is a bit deeper than the twin fans on
> > the K3/100.
> >
> > 73,
> >
> > Lyle KK7P
> >
> >  Is the form factor for the yet to be available KPA500 the same as my K3?
> >
> > ______________________________________________________________
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:[hidden email]
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html