KPOD- POWER Macro

[LDZ]

Message-ID: <[hidden email] <mailto:[hidden email]>>

Leroy

I would be interested to see the macro that you are using to set the power.

I too would like to be able to toggle a higher and lower power at the push of a button


73

Trevor Clapp
M6LDZ
2E0LDZ
[hidden email] <mailto:[hidden email]>

RADIO BLOG <http://chopcat.co.uk/page1/blog/index.html>

07900 49 77 11





______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Elecraft mailing list]

Hi Trevor,
For Macro Label QRO Tap F2  use PC100;Macro Label QRP Hold F2  use PC005; 
Of course you can use switch the order of hold and tap and use any matching pair of F keys and any value you want to toggle. See also Programmer's reference manual P.2 Table 1. 73, Charles N2SO
Treasurer, Quarter Century Wireless Association, Inc. http://QCWA.org 

    On Tuesday, September 6, 2016 5:42 AM, 2EØLDZ <[hidden email]> wrote:
 

 Message-ID: <[hidden email] <mailto:[hidden email]>>

Leroy

I would be interested to see the macro that you are using to set the power.

I too would like to be able to toggle a higher and lower power at the push of a button


73

Trevor Clapp
M6LDZ
2E0LDZ
[hidden email] <mailto:[hidden email]>

RADIO BLOG <http://chopcat.co.uk/page1/blog/index.html>

07900 49 77 11





______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]


   
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[Leroy]

In a TAP position I have   TUNE5W    PC005;SWH16;      goes into 5W tune,
Tap again it goes to operate.

In the corresponding HOLD I have  TUNE15W   PCO15;SWH16;   Goes to  5W
tune(I have the CONFIG TUNE PWR set to 5W), sets the drive level to 15W.
 TAP it again it goes to operate. That  gives me 475W out on 160mtrs. That
is TOO much drive for me on 6mtrs.

Works for me.

Leroy AB7CE

-----Original Message-----
From: Elecraft [mailto:[hidden email]] On Behalf Of 2EØLDZ
Sent: Tuesday, September 06, 2016 3:40 AM
To: [hidden email]
Subject: [Elecraft] KPOD- POWER Macro

Message-ID: <[hidden email]
<mailto:[hidden email]>>

Leroy

I would be interested to see the macro that you are using to set the power.

I too would like to be able to toggle a higher and lower power at the push
of a button


73

Trevor Clapp
M6LDZ
2E0LDZ
[hidden email] <mailto:[hidden email]>

RADIO BLOG <http://chopcat.co.uk/page1/blog/index.html>

07900 49 77 11





______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to [hidden email]


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]