KX1 3080 - no 80m

[Tod Glenn]

Help.  I just installed the 3080 module in my KX1 and I only get 30m  
- no 80.  I have firmware version 1.02, but when i cycle through band  
selection, I never see 80m.  Any suggestions?

----
Tod Glenn
N7JQW
NAQCC #1283
SKCC #1444
FISTS #12134
ARCI #12420
[hidden email]



_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Jim Younce]

Tod:

1.  Tap the "MENU" button and rotate the freq knob until "b30" appears.
2.  Tap the RIT button and "b80" will appear.
3.  Hold down the Menu button to enter the edit process and the display will
show "OFF".
4.  Turn the frequency knob to select "ON".
5.  Tap the "MENU" button again to exit the menu program.

Tapping the RIT button in the "b" menu toggles it between 30 and 80 meters.
I just ran into this myself yesterday as I was upgrading a KX1 that I built
for KA3BLD.

73
Jim K4ZM


_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Gene Hall]

Tod ... I had the same problem so I went back and read the book again.  The
30 and 80 meter bands have to be turned on in the set-up before it will show
up as a selectable band.  The 80 meter activation is the last sentence in
Step 1 of the Revision 1.02 Firmware new features.

I missed that last sentence my first time through.

Hopefully this will help you out.

  GL es 73 ... Gene ... W4TCO




On 5/6/06, Tod Glenn <[hidden email]> wrote:

>
> Help.  I just installed the 3080 module in my KX1 and I only get 30m
> - no 80.  I have firmware version 1.02, but when i cycle through band
> selection, I never see 80m.  Any suggestions?
>
> ----
> Tod Glenn
> N7JQW
> NAQCC #1283
> SKCC #1444
> FISTS #12134
> ARCI #12420
> [hidden email]
>
>
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Tod Glenn]

On May 6, 2006, at 7:09 AM, k4zm wrote:

> Tod:
>
> 1.  Tap the "MENU" button and rotate the freq knob until "b30"  
> appears.
> 2.  Tap the RIT button and "b80" will appear.
> 3.  Hold down the Menu button to enter the edit process and the  
> display will show "OFF".
> 4.  Turn the frequency knob to select "ON".
> 5.  Tap the "MENU" button again to exit the menu program.
>
> Tapping the RIT button in the "b" menu toggles it between 30 and 80  
> meters. I just ran into this myself yesterday as I was upgrading a  
> KX1 that I built for KA3BLD.
>
> 73
> Jim K4ZM

Thanks everyone.  I got it all working.

----
Tod Glenn
N7JQW
NAQCC #1283
SKCC #1444
FISTS #12134
ARCI #12420
[hidden email]



_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com