KX1 KXB30 Alignment

[Tony Morgan-2]

Hi Guys,
Have almost completed KX1 #770.
Everything is fine so far. My question is with the KXAT1 installed, how do I
get to trimmer 20A on the KX1 board?
In the KXB30 manual, page 7, last step it says to re-align rcvr on 20 mtrs.

Thanks,

Tony W7GO

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[David Toepfer]

Simply remove your kxat1, re-jumper pins 1 and 3 of j7 near the antenna jack,
and follow the Receiver Alignment procedure outlined on p45 of your kx1 manual.
 Then when this is doen, re-install your kxat1.

kb3ipe

dt
.

--- Tony Morgan <[hidden email]> wrote:

> Hi Guys,
> Have almost completed KX1 #770.
> Everything is fine so far. My question is with the KXAT1 installed, how do I
> get to trimmer 20A on the KX1 board?
> In the KXB30 manual, page 7, last step it says to re-align rcvr on 20 mtrs.
>
> Thanks,
>
> Tony W7GO
>
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft   
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Tony Morgan-2]

Thanks for the reply.
When I got up this morning and looked at the KX1, I knew I had a senior
moment last night!
I was looking a de-soldering the pins instead of lifting it out.
What do I know, I just built it!

Thanks,

Tony W7GO
----- Original Message -----
From: "David Toepfer" <[hidden email]>
To: "Tony Morgan" <[hidden email]>; "#elecraft"
<[hidden email]>
Sent: Thursday, August 12, 2004 1:02 AM
Subject: Re: [Elecraft] KX1 KXB30 Alignment


> Simply remove your kxat1, re-jumper pins 1 and 3 of j7 near the antenna
jack,
> and follow the Receiver Alignment procedure outlined on p45 of your kx1
manual.

>  Then when this is doen, re-install your kxat1.
>
> kb3ipe
>
> dt
> .
>
> --- Tony Morgan <[hidden email]> wrote:
>
> > Hi Guys,
> > Have almost completed KX1 #770.
> > Everything is fine so far. My question is with the KXAT1 installed, how

do I
> > get to trimmer 20A on the KX1 board?
> > In the KXB30 manual, page 7, last step it says to re-align rcvr on 20
mtrs.

> >
> > Thanks,
> >
> > Tony W7GO
> >
> > _______________________________________________
> > Elecraft mailing list
> > Post to: [hidden email]
> > You must be a subscriber to post to the list.
> > Subscriber Info (Addr. Change, sub, unsub etc.):
> > http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/subscribers.htm
> > Elecraft web page: http://www.elecraft.com
> >
>

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft   
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com