KX1 Receiver Deaf

[nlhouck]

It seems not all my emails are getting through, so if this is redundant please excuse me.  I built a KX1 with 3080 and tuner options.  Initially I had low audio but resolved by fixing a missed solder joint.  With that done, It passed the initial alignment and all seemed fine.  With proper ear buds the audio level is actually a bit loud for me.  Unfortunately, unless I touch the circuit board near U6 the unit is deaf.  Touching the board brings the unit to life and the receive is pretty good.  I've resoldered everything in the area.  Also checked voltages at U6.  They are ok, but about 0.5 v higher than spec'd on pins 5 and 6.  I've removed the tuner ( which seems to work ) and tested.  Could it be a CAP, since I'm a pretty big capacitive load?

The build was fun and I'm learning a lot, but could really use someone to help me clear the cobwebs and work through this problem.  Thanks in advance for any help you can offer as I'm anxious to play on the air.  I don't want to operate the unit with my finger stuck on the circuit board, I might give people the wrong impression of ham rado operators.

73 de
KC2MJT
Nate Houck
_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com

[Don Wilhelm-3]

Nate,

I replied to this a day or two ago, I guess you did not get it - so here is
what I sent.
--------------------------------------------------
The most likley problem is that you may not be getting a signal from the DDS
to pin 6 of the receive mixer (U6).

Does it transmit with good power?  If not, check L4 and L5 with an ohmmeter
to see if they are open - they are easily damaged when installing them.

If it transmits, then check C3 for correct value and proper soldering.  If
you have an RF Probe (or can construct one), check the RF Voltage at U6 pin
6 - it should be greater than 70 mV to meet the mixer specs, but the usual
amplitude is half a volt of more.

73,
Don W3FPR

> -----Original Message-----
> From: [hidden email]
> [mailto:[hidden email]]On Behalf Of nlhouck
> Sent: Friday, December 01, 2006 9:25 AM
> To: [hidden email]
> Subject: [Elecraft] KX1 Receiver Deaf
>
>
> It seems not all my emails are getting through, so if this is
> redundant please excuse me.  I built a KX1 with 3080 and tuner
> options.  Initially I had low audio but resolved by fixing a
> missed solder joint.  With that done, It passed the initial
> alignment and all seemed fine.  With proper ear buds the audio
> level is actually a bit loud for me.  Unfortunately, unless I
> touch the circuit board near U6 the unit is deaf.  Touching the
> board brings the unit to life and the receive is pretty good.
> I've resoldered everything in the area.  Also checked voltages at
> U6.  They are ok, but about 0.5 v higher than spec'd on pins 5
> and 6.  I've removed the tuner ( which seems to work ) and
> tested.  Could it be a CAP, since I'm a pretty big capacitive load?
>
> The build was fun and I'm learning a lot, but could really use
> someone to help me clear the cobwebs and work through this
> problem.  Thanks in advance for any help you can offer as I'm
> anxious to play on the air.  I don't want to operate the unit
> with my finger stuck on the circuit board, I might give people
> the wrong impression of ham rado operators.
>
> 73 de
> KC2MJT
> Nate Houck
> _______________________________________________
> Elecraft mailing list
> Post to: [hidden email]
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
>  http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.430 / Virus Database: 268.15.6/567 - Release Date:
> 12/4/2006 7:18 AM
>

--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.430 / Virus Database: 268.15.6/567 - Release Date: 12/4/2006
7:18 AM

_______________________________________________
Elecraft mailing list
Post to: [hidden email]
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
 http://mailman.qth.net/mailman/listinfo/elecraft   

Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com