Elecraft

KX3 ACC1 to PC and expert 1.3K-fa ?

Classic

List

Threaded

5 messages Options

Andre Bourbon

KX3 ACC1 to PC and expert 1.3K-fa ?

My setup is : KX3 --- PC ----Expert Ampli 1K-fa or 1.3k-fa

Using the ACC1 port :

Kx3 Connect to my pc with KXUSB cable and DX-lab logging prg --------- band
changing is ok

KX3 connect with my Expert ampli DB15 ( txd,rxd,gnd ) ( flex radio cat
settings ) -band changing is ok

I will do it now together :

I put 1 cable wired on parallel : txd, rxd, gnd

1 cable goes from the KX3 to the expert ampli

1 cable goes from the KX3 via KX3USB to the pc

----band changing totally NOT working any more .

Its look like there is a conflict or the voltage from the kx3 is to low to
change the band info to the pc and on the same time to the cat port (Expert
ampli.)

Any advice, or solution ???

André ON7YK

---
Deze e-mail is gecontroleerd op virussen door AVG.
http://www.avg.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

iw2noy

Re: KX3 ACC1 to PC and expert 1.3K-fa ?

Hi,

Serial communications is thinked for two buddies with crossed tx and rx., not for three.
You have too many tx on the same cable.
Remove the tx from the db15 of expert you don't need it. For the expert is enough READ (rx) the frequency that set the CAT coming from the PC (TX).
Remove the tx from the expert db 15 and try again.
I have similar setup but with k3s instead of kx3.
There are cable schemas on my site, if you want give a look.

Good luck, 73 de IW2NOY

http://www.iw2noy.it/index.php?id=87

⁣Inviato da BlueMail

Il giorno 1 mar 2018 09:53, alle ore 09:53, Andre Bourbon <[hidden email]> ha scritto:

>My setup is : KX3 --- PC ----Expert Ampli 1K-fa or 1.3k-fa
>
>
>
>Using the ACC1 port :
>
>
>
>Kx3 Connect to my pc with KXUSB cable and DX-lab logging prg ---------
>band
>changing is ok
>
>KX3 connect with my Expert ampli DB15 ( txd,rxd,gnd ) ( flex radio cat
>settings ) -band changing is ok
>
>
>
>I will do it now together :
>
>I put 1 cable wired on parallel : txd, rxd, gnd
>
> 1 cable goes from the KX3 to the expert ampli
>
> 1 cable goes from the KX3 via KX3USB to the pc
>
>
>
>----band changing totally NOT working any more .
>
>Its look like there is a conflict or the voltage from the kx3 is to low
>to
>change the band info to the pc and on the same time to the cat port
>(Expert
>ampli.)
>
>Any advice, or solution ???
>
>André ON7YK
>
>
>
>
>
>
>
>
>
>
>
>---
>Deze e-mail is gecontroleerd op virussen door AVG.
>http://www.avg.com
>______________________________________________________________
>Elecraft mailing list
>Home: http://mailman.qth.net/mailman/listinfo/elecraft
>Help: http://mailman.qth.net/mmfaq.htm
>Post: mailto:[hidden email]
>
>This list hosted by: http://www.qsl.net
>Please help support this email list: http://www.qsl.net/donate.html
>Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Andre Bourbon

Re: KX3 ACC1 to PC and expert 1.3K-fa ?

Hi,

Tnx

I have already test this configuration like you propose.

Removed the TX (pin9) on the DB15 only pin 1(rx) and 4 (gnd)

But the expert need as cat config Flex radio when he is on the KX3 , tx and Rx must be connected .

KX3 is not like K3

73’ André on7yk

From: Graziano Roccon [mailto:[hidden email]] On Behalf Of Graziano Roccon IW2NOY
Sent: donderdag 1 maart 2018 11:08
To: Andre Bourbon
Cc: [hidden email]
Subject: Re: [Elecraft] KX3 ACC1 to PC and expert 1.3K-fa ?

Hi,

Serial communications is thinked for two buddies with crossed tx and rx., not for three.

You have too many tx on the same cable.

Remove the tx from the db15 of expert you don't need it. For the expert is enough READ (rx) the frequency that set the CAT coming from the PC (TX).

Remove the tx from the expert db 15 and try again.

I have similar setup but with k3s instead of kx3.

There are cable schemas on my site, if you want give a look.

Good luck, 73 de IW2NOY

http://www.iw2noy.it/index.php?id=87

Inviato da BlueMail <http://www.bluemail.me/r?b=12200>

Il giorno 1 mar 2018, alle ore 09:53, Andre Bourbon <[hidden email]> ha scritto:

My setup is : KX3 --- PC ----Expert Ampli 1K-fa or 1.3k-fa

Using the ACC1 port :

Kx3 Connect to my pc with KXUSB cable and DX-lab logging prg --------- band

changing is ok

KX3 connect with my Expert ampli DB15 ( txd,rxd,gnd ) ( flex radio cat

settings ) -band changing is ok

I will do it now together :

I put 1 cable wired on parallel : txd, rxd, gnd

1 cable goes from the KX3 to the expert ampli

1 cable goes from the KX3 via KX3USB to the pc

----band changing totally NOT working any more .

Its look like there is a conflict or the voltage from the kx3 is to low to

change the band info to the pc and on the same time to the cat port (Expert

ampli.)

Any advice, or solution ???

André ON7YK

---

Deze e-mail is gecontroleerd op virussen door AVG.

http://www.avg.com

_____

Elecraft mailing list

Home: http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/mmfaq.htm

Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net

Please help support this email list: http://www.qsl.net/donate.html

Message delivered to [hidden email]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

Igor Sokolov-2

Re: KX3 ACC1 to PC and expert 1.3K-fa ?

In reply to this post by iw2noy

I have the same setup. KX3 and Expert 1.3

IW2NOY is correct. Expert only has to listen on CAT. Remove TX line
connection from Expert to TRX otherwise you will have collisions when
Expert and computer both are polling TRX for frequency.

I use Elecraft setting for CAT on Expert.

73, Igor UA9CDC

01.03.2018 15:58, Andre Bourbon пишет:

> Hi,
>
> Tnx
>
> I have already test this configuration like you propose.
>
> Removed the TX (pin9) on the DB15 only pin 1(rx) and 4 (gnd)
>
> But the expert need as cat config Flex radio when he is on the KX3 , tx and Rx must be connected .
>
>
>
> KX3 is not like K3
>
> 73’ André on7yk
>
>
>
>
>
> From: Graziano Roccon [mailto:[hidden email]] On Behalf Of Graziano Roccon IW2NOY
> Sent: donderdag 1 maart 2018 11:08
> To: Andre Bourbon
> Cc: [hidden email]
> Subject: Re: [Elecraft] KX3 ACC1 to PC and expert 1.3K-fa ?
>
>
>
> Hi,
>
> Serial communications is thinked for two buddies with crossed tx and rx., not for three.
>
> You have too many tx on the same cable.
>
> Remove the tx from the db15 of expert you don't need it. For the expert is enough READ (rx) the frequency that set the CAT coming from the PC (TX).
>
> Remove the tx from the expert db 15 and try again.
>
> I have similar setup but with k3s instead of kx3.
>
> There are cable schemas on my site, if you want give a look.
>
> Good luck, 73 de IW2NOY
>
> http://www.iw2noy.it/index.php?id=87
>
>
>
> Inviato da BlueMail <http://www.bluemail.me/r?b=12200>
>
> Il giorno 1 mar 2018, alle ore 09:53, Andre Bourbon <[hidden email]> ha scritto:
>
> My setup is : KX3 --- PC ----Expert Ampli 1K-fa or 1.3k-fa
>
>
>
>
>
>
>
>
>
>
>
> Using the ACC1 port :
>
>
>
>
>
>
>
>
>
>
>
> Kx3 Connect to my pc with KXUSB cable and DX-lab logging prg --------- band
>
>
> changing is ok
>
>
>
>
>
> KX3 connect with my Expert ampli DB15 ( txd,rxd,gnd ) ( flex radio cat
>
>
> settings ) -band changing is ok
>
>
>
>
>
>
>
>
>
>
>
> I will do it now together :
>
>
>
>
>
> I put 1 cable wired on parallel : txd, rxd, gnd
>
>
>
>
>
> 1 cable goes from the KX3 to the expert ampli
>
>
>
>
>
> 1 cable goes from the KX3 via KX3USB to the pc
>
>
>
>
>
>
>
>
>
>
>
> ----band changing totally NOT working any more .
>
>
>
>
>
> Its look like there is a conflict or the voltage from the kx3 is to low to
>
>
> change the band info to the pc and on the same time to the cat port (Expert
>
>
> ampli.)
>
>
>
>
>
> Any advice, or solution ???
>
>
>
>
>
> André ON7YK
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> ---
>
>
> Deze e-mail is gecontroleerd op virussen door AVG.
>
>
> http://www.avg.com
>
>
>
> _____
>
>
>
>
>
>
> Elecraft mailing list
>
>
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>
>
> Help: http://mailman.qth.net/mmfaq.htm
>
>
> Post: mailto:[hidden email]
>
>
>
>
>
> This list hosted by: http://www.qsl.net
>
>
> Please help support this email list: http://www.qsl.net/donate.html
>
>
> Message delivered to [hidden email]
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]

Andre Bourbon

Re: KX3 ACC1 to PC and expert 1.3K-fa ?

Hi Igor ,

Tnx for info .

On this moment I test the KX3 with the expert 1K-fa .

The settings for elecraft are not in the menu ( 1k-fa).

On the 1.3K-fa there are cat settings for elecraft .

I will try it when my 1.3K-fa is arrived , end of March .

73’ André

C5YK / C5S / (exC56YK ) / ON7YK

-----Original Message-----
From: [hidden email] [mailto:[hidden email]] On Behalf Of Igor Sokolov
Sent: vrijdag 2 maart 2018 4:03
To: [hidden email]
Subject: Re: [Elecraft] KX3 ACC1 to PC and expert 1.3K-fa ?

I have the same setup. KX3 and Expert 1.3

IW2NOY is correct. Expert only has to listen on CAT. Remove TX line

connection from Expert to TRX otherwise you will have collisions when

Expert and computer both are polling TRX for frequency.

I use Elecraft setting for CAT on Expert.

73, Igor UA9CDC

01.03.2018 15:58, Andre Bourbon пишет:

> Hi,

>

> Tnx

>

> I have already test this configuration like you propose.

>

> Removed the TX (pin9) on the DB15 only pin 1(rx) and 4 (gnd)

>

> But the expert need as cat config Flex radio when he is on the KX3 , tx and Rx must be connected .

>

>

>

> KX3 is not like K3

>

> 73’ André on7yk

>

>

>

>

>

> From: Graziano Roccon [mailto:[hidden email]] On Behalf Of Graziano Roccon IW2NOY

> Sent: donderdag 1 maart 2018 11:08

> To: Andre Bourbon

> Cc: [hidden email]

> Subject: Re: [Elecraft] KX3 ACC1 to PC and expert 1.3K-fa ?

>

>

>

> Hi,

>

> Serial communications is thinked for two buddies with crossed tx and rx., not for three.

>

> You have too many tx on the same cable.

>

> Remove the tx from the db15 of expert you don't need it. For the expert is enough READ (rx) the frequency that set the CAT coming from the PC (TX).

>

> Remove the tx from the expert db 15 and try again.

>

> I have similar setup but with k3s instead of kx3.

>

> There are cable schemas on my site, if you want give a look.

>

> Good luck, 73 de IW2NOY

>

> http://www.iw2noy.it/index.php?id=87

>

>

>

> Inviato da BlueMail <http://www.bluemail.me/r?b=12200>

>

> Il giorno 1 mar 2018, alle ore 09:53, Andre Bourbon <[hidden email]> ha scritto:

>

> My setup is : KX3 --- PC ----Expert Ampli 1K-fa or 1.3k-fa

>

>

>

>

>

>

>

>

>

>

>

> Using the ACC1 port :

>

>

>

>

>

>

>

>

>

>

>

> Kx3 Connect to my pc with KXUSB cable and DX-lab logging prg --------- band

>

>

> changing is ok

>

>

>

>

>

> KX3 connect with my Expert ampli DB15 ( txd,rxd,gnd ) ( flex radio cat

>

>

> settings ) -band changing is ok

>

>

>

>

>

>

>

>

>

>

>

> I will do it now together :

>

>

>

>

>

> I put 1 cable wired on parallel : txd, rxd, gnd

>

>

>

>

>

> 1 cable goes from the KX3 to the expert ampli

>

>

>

>

>

> 1 cable goes from the KX3 via KX3USB to the pc

>

>

>

>

>

>

>

>

>

>

>

> ----band changing totally NOT working any more .

>

>

>

>

>

> Its look like there is a conflict or the voltage from the kx3 is to low to

>

>

> change the band info to the pc and on the same time to the cat port (Expert

>

>

> ampli.)

>

>

>

>

>

> Any advice, or solution ???

>

>

>

>

>

> André ON7YK

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

>

> ---

>

>

> Deze e-mail is gecontroleerd op virussen door AVG.

>

>

> http://www.avg.com

>

>

>

> _____

>

>

>

>

>

>

> Elecraft mailing list

>

>

> Home: http://mailman.qth.net/mailman/listinfo/elecraft

>

>

> Help: http://mailman.qth.net/mmfaq.htm

>

>

> Post: mailto:[hidden email]

>

>

>

>

>

> This list hosted by: http://www.qsl.net

>

>

> Please help support this email list: http://www.qsl.net/donate.html

>

>

> Message delivered to [hidden email]

> ______________________________________________________________

> Elecraft mailing list

> Home: http://mailman.qth.net/mailman/listinfo/elecraft

> Help: http://mailman.qth.net/mmfaq.htm

> Post: mailto:[hidden email]

>

> This list hosted by: http://www.qsl.net

> Please help support this email list: http://www.qsl.net/donate.html

> Message delivered to [hidden email]

______________________________________________________________

Elecraft mailing list

Home: http://mailman.qth.net/mailman/listinfo/elecraft

Help: http://mailman.qth.net/mmfaq.htm

Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net

Please help support this email list: http://www.qsl.net/donate.html

Message delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]