KX3 beta firmware rev. 2.38: 15 Watts max output on 80-20 m, and PSK63 mode

[wayne burdick]

KX3 beta firmware rev. 2.38 is now available on our KX3 software page:

    http://www.elecraft.com/KX3/KX3_software.htm

See instructions on this page for loading beta releases.

This release includes two new features:

The new 15-watt level applies only to 80-20 meters, and is still considered somewhat experimental. Several dozen field testers have been using it with excellent results, but we can't guarantee that every KX3 will actually put out a full 15 W. Supply voltage is one limiting factor. We strongly recommend the use of 13.8-14 V whenever possible. This is especially important when you're driving an external amplifier and using one of the linear modes (SSB, AM, PSK-D, or audio data modes).

PSK63 is twice as fast as PSK31. Rather than copy it on the KX3's VFO B display, you may want to use the Terminal function of KX3 Utility, or use a PX3 with text decode turned on. This data mode is especially popular in Europe.

Rev. 2.38 also corrects a problem with some KX3-4M (70 MHz) modules that had lower than normal power output.

73,
Wayne
N6KR


* * *

MCU 2.38 / DSP 1.37, 01-03-2016

• POWER OUT NOW 15 WATTS MAX, 80-20 M: On 80-20 meters, the PWR control can now be set as high as 15 W (max is still 12 W on other bands). Supply voltage must be over 12.8 V on key-down as indicated by the KX3’s voltage display (tap DISP, rotate VFO B). Note: The KX3 will automatically reduce power as required if current, SWR, or temperature is excessive, or if supply voltage is too low. If a band other than 80-20 m is selected, power output will be cut back to 12 W max. It must then be manually set above 12 W after switching to 80-20 m.

• PSK63 MODE ADDED: Tap DATA, rotate VFO B until PSK D is displayed, then use VFO A to select 31 or 63 baud. The default is PSK31.  

• 4-METER POWER OUTPUT IMPROVED: Changed IF band-pass filter configuration to increase drive level on 4 meters. This should improve 4-meter power output in cases where it was marginal due to filter rolloff.


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]

[KI4D]

After uploading the new firmware to my SN#01741 KX-3 yesterday, I tried to
crank the power up to 15 watts on the dial, and found that 12 watts was as
high as it would display on 40 meters.  The unit was being powered by Pro
Audio Engineering PAE-Kx33.  Anyone else have this problem?

Don, KI4D

-----Original Message-----
From: Elecraft [mailto:[hidden email]] On Behalf Of Wayne
Burdick
Sent: Saturday, January 9, 2016 12:00 AM
To: Elecraft Reflector
Cc: [hidden email]
Subject: [Elecraft] KX3 beta firmware rev. 2.38: 15 Watts max output on
80-20 m, and PSK63 mode

KX3 beta firmware rev. 2.38 is now available on our KX3 software page:

    http://www.elecraft.com/KX3/KX3_software.htm

See instructions on this page for loading beta releases.

This release includes two new features:

The new 15-watt level applies only to 80-20 meters, and is still considered
somewhat experimental. Several dozen field testers have been using it with
excellent results, but we can't guarantee that every KX3 will actually put
out a full 15 W. Supply voltage is one limiting factor. We strongly
recommend the use of 13.8-14 V whenever possible. This is especially
important when you're driving an external amplifier and using one of the
linear modes (SSB, AM, PSK-D, or audio data modes).

PSK63 is twice as fast as PSK31. Rather than copy it on the KX3's VFO B
display, you may want to use the Terminal function of KX3 Utility, or use a
PX3 with text decode turned on. This data mode is especially popular in
Europe.

Rev. 2.38 also corrects a problem with some KX3-4M (70 MHz) modules that had
lower than normal power output.

73,
Wayne
N6KR


* * *

MCU 2.38 / DSP 1.37, 01-03-2016

. POWER OUT NOW 15 WATTS MAX, 80-20 M: On 80-20 meters, the PWR control can
now be set as high as 15 W (max is still 12 W on other bands). Supply
voltage must be over 12.8 V on key-down as indicated by the KX3's voltage
display (tap DISP, rotate VFO B). Note: The KX3 will automatically reduce
power as required if current, SWR, or temperature is excessive, or if supply
voltage is too low. If a band other than 80-20 m is selected, power output
will be cut back to 12 W max. It must then be manually set above 12 W after
switching to 80-20 m.

. PSK63 MODE ADDED: Tap DATA, rotate VFO B until PSK D is displayed, then
use VFO A to select 31 or 63 baud. The default is PSK31.  

. 4-METER POWER OUTPUT IMPROVED: Changed IF band-pass filter configuration
to increase drive level on 4 meters. This should improve 4-meter power
output in cases where it was marginal due to filter rolloff.


______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to [hidden email]

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]