LCD Diffuser SPACERS? K2 # 5422?
Locked
 
|
I'm building K2 #5422, doing Front Panel board now!
I seem to be MISSING the two (2) 3/4" (19mm) LONG SPACERS mentioned on page 26, for putting over leads of each backlight LED shown in figure 5.9? No were to be found, as far as I can see. WHAT DO THEY LOOK LIKE? Paper? Plastic? Temporary? Home made? There are no "spacers" mentioned in appendix of photos for this Front Panel PCboard either? Help Thanks, 73's Fred N3CSY Spring Hill, FL __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
Fred,
They are part of the pieces PC board that is seen in fig. 5-1 That is the switch spacing tool. Part of it are the spacers. 73, Peter PA0PJE F and J schreef: > I'm building K2 #5422, doing Front Panel board now! > > I seem to be MISSING the two (2) 3/4" (19mm) LONG > SPACERS mentioned on page 26, for putting over leads > of each backlight LED shown in figure 5.9? > > No were to be found, as far as I can see. WHAT DO > THEY LOOK LIKE? Paper? Plastic? Temporary? > Home made? > > There are no "spacers" mentioned in appendix of > photos for this Front Panel PCboard either? > > Help > Thanks, 73's > Fred N3CSY > Spring Hill, FL > > __________________________________________________ > Do You Yahoo!? > Tired of spam? Yahoo! Mail has the best spam protection around > http://mail.yahoo.com > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
|
|
Oh and btw, Fred,
This is on the same page; <quote> Locate the Spacer Set PC board (Figure 5-1). Using long-nose pliers, carefully break out the pushbutton switch spacing tool and the four backlight LED spacers. Break the material only at the four indicated points. Note: The switch spacing tool doubles as the PC board for the RF probe, which will be assembled later. <unquote> 73, Peter ----- Oorspronkelijk bericht ----- Van: "PAøPJE" <[hidden email]> Aan: <[hidden email]> Verzonden: zaterdag 25 maart 2006 17:47 Onderwerp: Re: [Elecraft] LCD Diffuser SPACERS? K2 # 5422? > Fred, > > They are part of the pieces PC board that is seen in fig. 5-1 > That is the switch spacing tool. Part of it are the spacers. > > 73, > Peter PA0PJE > > F and J schreef: >> I'm building K2 #5422, doing Front Panel board now! >> >> I seem to be MISSING the two (2) 3/4" (19mm) LONG >> SPACERS mentioned on page 26, for putting over leads >> of each backlight LED shown in figure 5.9? >> >> No were to be found, as far as I can see. WHAT DO >> THEY LOOK LIKE? Paper? Plastic? Temporary? >> Home made? >> >> There are no "spacers" mentioned in appendix of >> photos for this Front Panel PCboard either? >> >> Help >> Thanks, 73's >> Fred N3CSY >> Spring Hill, FL >> >> __________________________________________________ >> Do You Yahoo!? >> Tired of spam? Yahoo! Mail has the best spam protection around >> http://mail.yahoo.com _______________________________________________ >> Elecraft mailing list >> Post to: [hidden email] >> You must be a subscriber to post to the list. >> Subscriber Info (Addr. Change, sub, unsub etc.): >> http://mailman.qth.net/mailman/listinfo/elecraft Help: >> http://mailman.qth.net/subscribers.htm >> Elecraft web page: http://www.elecraft.com >> > _______________________________________________ > Elecraft mailing list > Post to: [hidden email] > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |