Macro help needed

[Joe K2UF]

I have two macros one on 'm1' and one on 'm2'.  Both enable 'split' and
'sub' (swt48).  M1  splits up 1  and m2 splits up two.  I hit m1  radio is
split and sub is on.  The problem is if  if I hit m1 or m2 again 'sub' gets
turned off.  Is there a way I can check if 'sub' is on then not execute the
swt48?

Joe K2UF

No trees were harmed in the sending of this e-mail; however, many electrons
were inconvenienced.



______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[wayne burdick]

Hi Joe,

You can turn the sub RX on/off using "SB1;" and "SB0;". No need to use  
the SWT48 switch emulation command, which toggles.

73,
Wayne
N6KR

On Jan 7, 2012, at 12:33 PM, Joe K2UF wrote:

> I have two macros one on 'm1' and one on 'm2'.  Both enable 'split'  
> and
> 'sub' (swt48).  M1  splits up 1  and m2 splits up two.  I hit m1  
> radio is
> split and sub is on.  The problem is if  if I hit m1 or m2 again  
> 'sub' gets
> turned off.  Is there a way I can check if 'sub' is on then not  
> execute the
> swt48?
>
> Joe K2UF
>
> No trees were harmed in the sending of this e-mail; however, many  
> electrons
> were inconvenienced.
>
>
>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Dick Dievendorff]

See if the SB prigrammer's reference command works better for you than a switch tap toggle.

Dick, K6KR

On Jan 7, 2012, at 12:33, "Joe K2UF" <[hidden email]> wrote:

> I have two macros one on 'm1' and one on 'm2'.  Both enable 'split' and
> 'sub' (swt48).  M1  splits up 1  and m2 splits up two.  I hit m1  radio is
> split and sub is on.  The problem is if  if I hit m1 or m2 again 'sub' gets
> turned off.  Is there a way I can check if 'sub' is on then not execute the
> swt48?
>
> Joe K2UF
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html