Elecraft

Microkeyer II vs K3s

classic Classic list List threaded Threaded
♦
♦
 3 messages Options
john@kk9a.com
Reply | Threaded
Open this post in threaded view
♦
♦
|

Microkeyer II vs K3s

john@kk9a.com
Is the K3S RS232 set to 38400 b?

From HK3W
Wed May 25 07:41:45 EDT 2016

The Microham program does not recognize de K3

This is how I have it connected:

1. The Y cable is conected to the K3S ACC port.
2. One of the Y legs goes to the MicroHam's ACC.
3. The other leg of the Y cable goes to the XCVR port on the KAT500.
4. The E8504643 cable goes from the KAT500 (AMP) to the KPA500 AUX1 port.
5. The Microham RS232 cable is connected to the PC port on the P3.
6. The XCVR port on the P3 is connected to the RS232/P3 port on the K3.

I have a leftover Y cable as Elecraft sent me 2.
I use 38400 bps in baud rate
I have K3S + P3 +KAT500+KPA500
Regards
Siso HK3W

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
john@kk9a.com
Reply | Threaded
Open this post in threaded view
♦
♦
|

Re: Microkeyer II vs K3s

john@kk9a.com
 

Check the internal jumpers. I assume that you assigned a com port and
selected K3 38400 in the router. I have four DigiKeyer IIs and I can
only get three working with the K3S . The fourth unit worked fine when I
previously used it with a Yaesu but I cannot get it to work with my K3S
for some reason.

John KK9A

On 2016-05-25 13:49, Francisco "Siso" Hennessey HK3W wrote:

> Yes John, 38400bps
>
> 2016-05-25 12:45 GMT-05:00 [hidden email] <[hidden email]>:
>
>> Is the K3S RS232 set to 38400 b?
>>
>> From HK3W
>> Wed May 25 07:41:45 EDT 2016
>>
>> The Microham program does not recognize de K3
>>
>> This is how I have it connected:
>>
>> 1. The Y cable is conected to the K3S ACC port.
>> 2. One of the Y legs goes to the MicroHam's ACC.
>> 3. The other leg of the Y cable goes to the XCVR port on the KAT500.
>> 4. The E8504643 cable goes from the KAT500 (AMP) to the KPA500 AUX1 port.
>> 5. The Microham RS232 cable is connected to the PC port on the P3.
>> 6. The XCVR port on the P3 is connected to the RS232/P3 port on the K3.
>>
>> I have a leftover Y cable as Elecraft sent me 2.
>> I use 38400 bps in baud rate
>> I have K3S + P3 +KAT500+KPA500
>> Regards
>> Siso HK3W
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft [1]
>> Help: http://mailman.qth.net/mmfaq.htm [2]
>> Post: mailto:[hidden email]
>>
>> This list hosted by: http://www.qsl.net [3]
>> Please help support this email list: http://www.qsl.net/donate.html [4]
>> Message delivered to [hidden email]
>
> --
>
> ______________________________________________________________________
>
> FRANCISCO "SISO" HENNESSEY - H K 3 W ---
>
> ARRL DXCC CARD CHECKER
>
> DXCC HR - DXCC CW - DXCC RTTY -DXCC SSB - 8BDXCC - | Skype: siso-hk3w | TWITTER: HTTP://TWITTER.COM/HK3W [5] |
>
> MEMBER OF: ARRL (LM) - LOTW -

 

Links:
------
[1] http://mailman.qth.net/mailman/listinfo/elecraft
[2] http://mailman.qth.net/mmfaq.htm
[3] http://www.qsl.net
[4] http://www.qsl.net/donate.html
[5] http://twitter.com/HK3W
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
Joe Subich, W4TV-4
Reply | Threaded
Open this post in threaded view
♦
♦
|

Re: Microkeyer II vs K3s

Joe Subich, W4TV-4

On 5/25/2016 2:08 PM, [hidden email] wrote:
 >
 > Check the internal jumpers.

The only internal jumpers in microKEYER II control bias to the front
and back mic jacks.

> The fourth unit worked fine when I previously used it with a Yaesu
> but I cannot get it to work with my K3S for some reason.

Check your cables - particularly the RJ45 connector on the *Elecraft*
supplied E980287 RJ45 to DE9 (9 pin female) cable.  I have seen several
reports of intermittent connection in the RJ45 plug/jack.

73,

    ... Joe, W4TV


On 5/25/2016 2:08 PM, [hidden email] wrote:

>
>
> Check the internal jumpers. I assume that you assigned a com port and
> selected K3 38400 in the router. I have four DigiKeyer IIs and I can
> only get three working with the K3S . The fourth unit worked fine when I
> previously used it with a Yaesu but I cannot get it to work with my K3S
> for some reason.
>
> John KK9A
>
> On 2016-05-25 13:49, Francisco "Siso" Hennessey HK3W wrote:
>
>> Yes John, 38400bps
>>
>> 2016-05-25 12:45 GMT-05:00 [hidden email] <[hidden email]>:
>>
>>> Is the K3S RS232 set to 38400 b?
>>>
>>> From HK3W
>>> Wed May 25 07:41:45 EDT 2016
>>>
>>> The Microham program does not recognize de K3
>>>
>>> This is how I have it connected:
>>>
>>> 1. The Y cable is conected to the K3S ACC port.
>>> 2. One of the Y legs goes to the MicroHam's ACC.
>>> 3. The other leg of the Y cable goes to the XCVR port on the KAT500.
>>> 4. The E8504643 cable goes from the KAT500 (AMP) to the KPA500 AUX1 port.
>>> 5. The Microham RS232 cable is connected to the PC port on the P3.
>>> 6. The XCVR port on the P3 is connected to the RS232/P3 port on the K3.
>>>
>>> I have a leftover Y cable as Elecraft sent me 2.
>>> I use 38400 bps in baud rate
>>> I have K3S + P3 +KAT500+KPA500
>>> Regards
>>> Siso HK3W
>>>
>>> ______________________________________________________________
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft [1]
>>> Help: http://mailman.qth.net/mmfaq.htm [2]
>>> Post: mailto:[hidden email]
>>>
>>> This list hosted by: http://www.qsl.net [3]
>>> Please help support this email list: http://www.qsl.net/donate.html [4]
>>> Message delivered to [hidden email]
>>
>> --
>>
>> ______________________________________________________________________
>>
>> FRANCISCO "SISO" HENNESSEY - H K 3 W ---
>>
>> ARRL DXCC CARD CHECKER
>>
>> DXCC HR - DXCC CW - DXCC RTTY -DXCC SSB - 8BDXCC - | Skype: siso-hk3w | TWITTER: HTTP://TWITTER.COM/HK3W [5] |
>>
>> MEMBER OF: ARRL (LM) - LOTW -
>
>
>
> Links:
> ------
> [1] http://mailman.qth.net/mailman/listinfo/elecraft
> [2] http://mailman.qth.net/mmfaq.htm
> [3] http://www.qsl.net
> [4] http://www.qsl.net/donate.html
> [5] http://twitter.com/HK3W
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[hidden email]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [hidden email]
>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [hidden email]
Free forum by Nabble Edit this page