Newbie questions
Locked
 
|
I'm Urb, W1UL. Between 1949 and 2012 I was W2DEC. One of my good friends
tells people I've been a ham so long that my first call had a Roman Numeral :-) I'm sure these two questions have been asked many times and I apologize in advance. Is there a simple way to get back to the default configuration on a K3, I have my screwed up beyond recognition Number two, is their a downloadable program - not necessarily free - that will save the K3 configuration and reloading the saved configuration? Thanks for your help. Urb W1UL --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Urb
It is easy: 1.You can reset everything by the following: Power off Hold in shift knob while pressing power on switch unit it fully powers up You will have to start over again just like you had just finished building it - so don't so this just for grins If you have an older configuration file saved you can reload it and be right back where you were when you saved the file. The firmware is not affected either way - kinda like a restore point in Win XP. 2. The K3 utility program available "FREE" on their webste will do all that. I would suggest that once you do a "reset" as above save it with the utility program so you can always undo what you done did 73 K2TTT (Jay)C6ATT ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
|
Hi Urb,
Jay is quite correct. The latest K3 Utility Program is here: http://www.elecraft.com/K3/k3_software.htm - 73 and good DX de Mike, K6MKF, President - NCDXC, IDXC 2015, W6NAG, IDXG, ADXG, RRC #933, K3-P3-KPA500-KAT500 Addict, Maui -----Original Message----- From: Elecraft [mailto:[hidden email]] On Behalf Of Jay K2TTT Sent: Monday, September 15, 2014 10:06 AM To: 'Urb LeJeune'; [hidden email] Subject: Re: [Elecraft] Newbie questions Urb It is easy: 1.You can reset everything by the following: Power off Hold in shift knob while pressing power on switch unit it fully powers up You will have to start over again just like you had just finished building it - so don't so this just for grins If you have an older configuration file saved you can reload it and be right back where you were when you saved the file. The firmware is not affected either way - kinda like a restore point in Win XP. 2. The K3 utility program available "FREE" on their webste will do all that. I would suggest that once you do a "reset" as above save it with the utility program so you can always undo what you done did 73 K2TTT (Jay)C6ATT ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
|
Administrator
|
Also, if your K3 was factory built and is not one of the earlier units shipped,
we usually have the original factory config file recorded here. Contact [hidden email] and they can help you out. Eric elecraft.com On 9/15/2014 10:18 AM, Mike Flowers wrote: > Hi Urb, > > Jay is quite correct. The latest K3 Utility Program is here: > http://www.elecraft.com/K3/k3_software.htm > > - 73 and good DX de Mike, K6MKF, President - NCDXC, IDXC 2015, W6NAG, IDXG, > ADXG, RRC #933, K3-P3-KPA500-KAT500 Addict, Maui > > > -----Original Message----- > From: Elecraft [mailto:[hidden email]] On Behalf Of Jay > K2TTT > Sent: Monday, September 15, 2014 10:06 AM > To: 'Urb LeJeune'; [hidden email] > Subject: Re: [Elecraft] Newbie questions > > Urb > > It is easy: > 1.You can reset everything by the following: > > Power off > Hold in shift knob while pressing power on switch unit it fully powers > up > > You will have to start over again just like you had just finished > building it - so don't so this just for grins > > If you have an older configuration file saved you can reload it and be > right back where you were when you saved the file. The firmware > is not affected either way - kinda like a restore point in Win XP. > > 2. The K3 utility program available "FREE" on their webste will do all > that. > I would suggest that once you do a "reset" as above save it with the > utility program so you can always undo what you done did > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[hidden email] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [hidden email] |
«
Return to Elecraft
|
1 view|%1 views
| Free forum by Nabble | Edit this page |