POWER SETTING DISPLAY

[N5AG]

Hello Elecraft,
Can the K3 Sub Receiver display (without the 2nd receiver installed) be programmed to show the power setting as a selectable continuous display as opposed to the power setting flashing when the PWR knob is turned?

I have no use for TIME display or DATE for instance. If the power setting was displayed continuously, we would not have to turn the PWR knob to see what the current power output was.

Thanks for the consideration,
Allen Griffith  N5AG  K3 #03547
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Val-12]

I wish we had there the CW speed too. There is a place for both values.

73, Val LZ1VB

Hello Elecraft,
Can the K3 Sub Receiver display (without the 2nd receiver installed) be
programmed to show the power setting as a selectable continuous display as
opposed to the power setting flashing when the PWR knob is turned?

I have no use for TIME display or DATE for instance. If the power setting
was displayed continuously, we would not have to turn the PWR knob to see
what the current power output was.

Thanks for the consideration,
Allen Griffith N5AG K3 #03547

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Bill Frantz]

I'd rather have the DSP filter information. High and low cutoff
or center frequency and bandwidth depending on which mode is set
for the controls.

YMMV - Bill, AE6JV

On 5/6/13 at 9:55 PM, [hidden email] (Val) wrote:

>I wish we had there the CW speed too. There is a place for both values.
>
>73, Val LZ1VB
>
>Can the K3 Sub Receiver display (without the 2nd receiver
>installed) be programmed to show the power setting as a
>selectable continuous display as opposed to the power setting
>flashing when the PWR knob is turned?
>...
>Allen Griffith N5AG K3 #03547

-----------------------------------------------------------------------
Bill Frantz        | I don't have high-speed      | Periwinkle
[phone]      | internet. I have DSL.        | 16345
Englewood Ave
www.pwpconsult.com |                              | Los Gatos,
CA 95032

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Gary Gregory-2]

I would rather see a lot more options to display in VFO B...everyone would
be happy then...:-)

73

On 6 May 2013 15:06, Bill Frantz <[hidden email]> wrote:

> I'd rather have the DSP filter information. High and low cutoff or center
> frequency and bandwidth depending on which mode is set for the controls.
>
> YMMV - Bill, AE6JV
>
> On 5/6/13 at 9:55 PM, [hidden email] (Val) wrote:
>
>  I wish we had there the CW speed too. There is a place for both values.
>>
>> 73, Val LZ1VB
>>
>> Can the K3 Sub Receiver display (without the 2nd receiver installed) be
>> programmed to show the power setting as a selectable continuous display as
>> opposed to the power setting flashing when the PWR knob is turned?
>> ...
>> Allen Griffith N5AG K3 #03547
>>
>
> ------------------------------**------------------------------**
> -----------
> Bill Frantz        | I don't have high-speed      | Periwinkle
> [phone]      | internet. I have DSL.        | 16345 Englewood Ave
> www.pwpconsult.com |                              | Los Gatos, CA 95032
>
> ______________________________**______________________________**__
> Elecraft mailing list
> Home: http://mailman.qth.net/**mailman/listinfo/elecraft<http://mailman.qth.net/mailman/listinfo/elecraft>
> Help: http://mailman.qth.net/mmfaq.**htm<http://mailman.qth.net/mmfaq.htm>
> Post: mailto:[hidden email].**net <[hidden email]>
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
>

--
*Gary - VK1ZZ
Skype: Gary.VK1ZZ
Motorhome Portable
The Shack*
*Elecraft K3
P3 Panadapter
KPA500FT
KAT500FT**
KX3-K
*
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Bob-270]

Well not quite everyone.  As a subreceiver owner I love the concept and would
suggest that this feature be available for all.  I can see it being there when
the subreceiver is not in use..   That could another option to select.

Admittedly I have no clue as to how much programming effort we are asking for
and also at some point there will be hardware limitations too.  The program and
setting storage space is not infinite.

The use of the subreceiver  in my case is pretty limited to split usage while
chasing DX.   It can be seen on the P3 so maybe even a "Marco" to turn it on or
off could be used too.

73,
Bob
K2TK  ex KN2TKR (1956) & K2TKR .



On 5/6/2013 1:40 AM, Gary Gregory wrote:

> I would rather see a lot more options to display in VFO B...everyone would
> be happy then...:-)
>
> 73
>
> On 6 May 2013 15:06, Bill Frantz <[hidden email]> wrote:
>
>> I'd rather have the DSP filter information. High and low cutoff or center
>> frequency and bandwidth depending on which mode is set for the controls.
>>
>> YMMV - Bill, AE6JV
>>
>> On 5/6/13 at 9:55 PM, [hidden email] (Val) wrote:
>>
>>   I wish we had there the CW speed too. There is a place for both values.
>>> 73, Val LZ1VB
>>>
>>> Can the K3 Sub Receiver display (without the 2nd receiver installed) be
>>> programmed to show the power setting as a selectable continuous display as
>>> opposed to the power setting flashing when the PWR knob is turned?
>>> ...
>>> Allen Griffith N5AG K3 #03547
>>>

______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[hidden email]

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html