Hi,
I have steadily and carefully built my K2 and it has passed all the tests so far with flying colours, including 40m RX. Now I have just completed the transmitter stages, and attempted the first tx test... Ah problems. Well things have gone well so far!! Even a bottle of Hoegaarden did not help... This is what happens. 1.40m rx working fine. 2. Connect dummy load etc 3. Set for 2.0 output, tune to 7100 4. Press and hold tune. A bleep in the headphones, the output limiter on the PSU flicks in cutting the power briefly and Elecraft displays on the K2. (I have tried another PSU (3amp) but the same result) If the power is turned down to .2 or so it will stay in tune mode Upon checking the antenna connection, there appears to be a short between earth and the centre of the BNC.. (Using a DVM) This cannot be correct? I have tried another PSU (3amp) but the same result. Perhaps you could confirm if an indicated short across the BNC, is incorrect, and any suggestions of where to look first would be very helpful. Thanks!!!!! Regards Nicolas www.m1hog.com --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.716 / Virus Database: 472 - Release Date: 05/07/2004 _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Hi
It is normal to read a very low DC resistance on the BNC center pin to ground. I would look for bad connections on the toroids in the transmitter and make sure T4 is wound right and connected right. Also check that Q2 is in right and all of the 1n4007 diodes are in right Don Brown ----- Original Message ----- From: Nicolas Pike<mailto:[hidden email]> To: [hidden email]<mailto:[hidden email]> Sent: Friday, July 09, 2004 6:40 PM Subject: [Elecraft] RE: K2 4039, Failing transmitter tests Hi, I have steadily and carefully built my K2 and it has passed all the tests so far with flying colours, including 40m RX. Now I have just completed the transmitter stages, and attempted the first tx test... Ah problems. Well things have gone well so far!! Even a bottle of Hoegaarden did not help... This is what happens. 1.40m rx working fine. 2. Connect dummy load etc 3. Set for 2.0 output, tune to 7100 4. Press and hold tune. A bleep in the headphones, the output limiter on the PSU flicks in cutting the power briefly and Elecraft displays on the K2. (I have tried another PSU (3amp) but the same result) If the power is turned down to .2 or so it will stay in tune mode Upon checking the antenna connection, there appears to be a short between earth and the centre of the BNC.. (Using a DVM) This cannot be correct? I have tried another PSU (3amp) but the same result. Perhaps you could confirm if an indicated short across the BNC, is incorrect, and any suggestions of where to look first would be very helpful. Thanks!!!!! Regards Nicolas www.m1hog.com<http://www.m1hog.com/> --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com<http://www.grisoft.com/>). Version: 6.0.716 / Virus Database: 472 - Release Date: 05/07/2004 _______________________________________________ Elecraft mailing list Post to: [hidden email]<mailto:[hidden email]> You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft<http://mailman.qth.net/mailman/listinfo/elecraft> Help: http://mailman.qth.net/subscribers.htm<http://mailman.qth.net/subscribershtm> Elecraft web page: http://www.elecraft.com<http://www.elecraft.com/> _______________________________________________ Elecraft mailing list Post to: [hidden email] You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com |
Free forum by Nabble | Edit this page |